Asus P2B-F P2B-F User Manual - Page 22

ASUS Smart Thermal Solutions

Get Asus P2B-F PDF manuals and user guides View all Asus P2B-F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

III. H/W SETUP CPU III. HARDWARE SETUP ASUS Smart Thermal Solutions ASUS provides two smart solutions to Slot 1 CPU thermal problems: the ASUS Smart Fan or ASUS S-P2FAN and the ASUS P2T-Cable. ASUS S-P2FAN The optional ASUS Smart Fan or ASUS S-P2FAN is a CPU fan for a Pentium® II processor packaged in an SECC. Unlike other CPU thermal solutions, the ASUS S-P2FAN has an integrated thermal sensor located near the center of the CPU heat source. The sensor is optimized by ASUS to give the most accurate reading of the CPU temperature, thus provides the best protection to your computer system. Thermal Cable CPU Fan Cable (2 black wires) (3 colored wires) To Use the ASUS S-P2FAN See 2. Attach the Heatsink on the preceding page for the relevant procedures. Note that the S-P2FAN comes with a rock arm design for easy FAN/CPU installation. ASUS P2T-Cable The optional ASUS P2T-Cable can be used for a Pentium® III/II processor pack- aged in an SECC2/SECC or a Celeron™ Sensor processor packaged in an SEPP. NOTE: The ASUS P2T-Cable can only be used in a Slot 1 motherboard with a 2-pin thermal sensor connector. Sensor Connector Plug To Use the ASUS P2T-Cable NOTE: The following procedures assume that you have properly attached a heatsink onto an SECC/SECC2/SEPP. 1. Simply peel off the tab from the sensor and then stick the sensor near the middle edge of the Intel boxed processor heatsink with fan (middle) or to either the upper or lower edge of the Celeron™ heatsink (right), as indicated. Tab Sensor ← OR STICK ABOUT HERE 22 ASUS P2B-F User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
22
ASUS P2B-F User’s Manual
III. HARDWARE SETUP
CPU
III. H/W SETUP
ASUS Smart Thermal Solutions
ASUS provides two smart solutions to Slot 1 CPU thermal problems: the
ASUS
Smart Fan
or
ASUS S-P2FAN
and the
ASUS P2T-Cable
.
ASUS S-P2FAN
The optional ASUS Smart Fan or ASUS S-P2FAN is a
CPU fan for a Pentium
®
II processor packaged in an SECC.
Unlike other CPU thermal solutions, the ASUS S-P2FAN
has an integrated thermal sensor located near the center
of the CPU heat source. The sensor is optimized by ASUS
to give the most accurate reading of the CPU tempera-
ture, thus provides the best protection to your computer
system.
To Use the ASUS S-P2FAN
See
2. Attach the Heatsink
on the preceding page for the relevant procedures. Note
that the S-P2FAN comes with a rock arm design for easy FAN/CPU installation.
ASUS P2T-Cable
The optional ASUS P2T-Cable can be
used for a Pentium
®
III/II processor pack-
aged in an SECC2/SECC or a Celeron™
processor packaged in an SEPP.
NOTE:
The ASUS P2T-Cable can only
be used in a Slot 1 motherboard with a
2-pin thermal sensor connector.
To Use the ASUS P2T-Cable
NOTE:
The following procedures assume that you have properly attached a
heatsink onto an SECC/SECC2/SEPP.
1.
Simply peel off the tab from the sensor and then stick the sensor near the middle
edge of the Intel boxed processor heatsink with fan (middle) or to either the
upper or lower edge of the Celeron™ heatsink (right), as indicated.
Sensor Connector Plug
Sensor
CPU Fan Cable
(3 colored wires)
Thermal Cable
(2 black wires)
Tab
Sensor
←
OR STICK ABOUT HERE