BenQ W1050 User Manual - Page 30

Disabling the password function, Switching input signal

Get BenQ W1050 PDF manuals and user guides View all BenQ W1050 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Keep this manual in a safe place. 6. Confirm the new password by re-entering the new password. 7. You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started. 8. To leave the OSD menu, press MENU on the projector or remote control. Disabling the password function To disable password protection, go back to the System Setup: Advanced > Password > Power On Lock menu and press OK on the projector or the remote control. The message 'Input Password' displays. Enter the current password. • If the password is correct, the OSD menu returns to the Power On Lock with the highlight of Off. • If the password is incorrect, the password error message displays lasting for three seconds, and the message 'Input Password' displays for your retry. You can press BACK on the projector or remote control to cancel the change or try another password. Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password. Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals. Be sure the Auto Source Search* function is On (which is the default of this projector) if you want the projector to automatically search for the signals. *You can set Auto Source Search function in the Basic menu when the projector is without input signal or in the Advanced menu > System Setup: Basic menu. You can also manually cycle through the available input signals. 1. Press SOURCE on the projector or remote control. A source selection bar displays. 30 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Operation
30
Keep this manual in a safe place.
6.
Confirm the new password by re-entering the new password.
7.
You have successfully assigned a new password to the projector. Remember to
enter the new password next time the projector is started.
8.
To leave the OSD menu, press
MENU
on the projector or remote control
.
Disabling the password function
To disable password protection, go back to the
System Setup: Advanced
>
Password > Power On Lock
menu and press
OK
on the projector or the remote
control. The message
'Input Password'
displays. Enter the current password.
•
If the password is correct, the OSD menu returns to the Power On Lock
with the highlight of Off.
•
If the password is incorrect, the password error message displays lasting for
three seconds, and the message 'Input Password' displays for your retry.
You can press BACK
on the projector or remote control
to cancel the
change or try another password.
Though the password function is disabled, you need to keep the old password in
hand should you ever need to re-activate the password function by entering the old
password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can
only display one full screen at a time. When starting up, the projector automatically
searches for the available signals.
Be sure the
Auto Source Search
* function is On (which is the default of this
projector) if you want the projector to automatically search for the signals.
*You can set
Auto Source Search
function in the Basic menu when the projector
is without input signal or in the Advanced menu > System Setup: Basic menu.
You can also manually cycle through the available input signals.
1.
Press
SOURCE
on the projector or
remote control. A source selection bar
displays.