BenQ W1050 User Manual - Page 41

Personalizing the projector menu display, Select the lamp saver mode

Page 41 highlights

To unlock the keys, press and hold on the projector or remote control for 3 seconds. Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Language in the Advanced menu > System Setup: Basic menu sets your familiar language for the OSD menus. Press OK on the projector or remote control to display language page. Use / / / and OK on the projector or remote control to select your language. • Menu Type in the Basic menu or in the Advanced menu > System Setup: Basic > Menu Settings menu sets the menu type. Use / to select a preferred type. • Menu Position in the Advanced menu > System Setup: Basic > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. • Menu Display Time in the Advanced menu > System Setup: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. • Blank Reminder Message in the Advanced menu > System Setup: Basic > Menu Settings menu sets whether to display reminder messages on screen. Use / to select your desired setting. • Splash Screen in the Advanced menu > System Setup: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Select the lamp saver mode 1. Open the OSD menu and go to the Advanced menu > Picture > Lamp Power menu. 2. Press / to select Normal/Economic/SmartEco. The lamp brightness vary from the different lamp mode,see the description list in table below. Lamp Power Description Normal Economic SmartEco Provides full lamp brightness Lower brightness to extend the lamp life and decreases the fan noise Adjusts the lamp power automatically depending on the content brightness level If the Economic mode or SmartEco mode is selected, the light output will be reduced and result in darker projected pictures. Operation 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73

Operation
41
To unlock the keys, press and hold
on the projector or remote control for 3
seconds.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
Language
in the
Advanced menu
>
System Setup: Basic
menu sets your
familiar language for the OSD menus. Press
OK
on the projector or remote
control to display language page. Use
/
/
/
and
OK
on the projector or
remote control to select your language.
Menu Type
in the
Basic menu
or in the
Advanced menu
>
System Setup:
Basic
>
Menu Settings
menu sets the menu type. Use
/
to select a
preferred type.
Menu Position
in the
Advanced menu
>
System Setup: Basic
>
Menu
Settings
menu sets the OSD position in five locations. Use
/
to select a
preferred position.
Menu Display Time
in the
Advanced menu
>
System Setup: Basic
>
Menu Settings
menu sets the length of time the OSD will remain active after
your last key press. The time length ranges from 5 to 30 seconds in 5-second
increments. Use
/
to select a suitable time frame.
Blank Reminder Message
in the
Advanced menu
>
System Setup: Basic
>
Menu Settings
menu sets whether to display reminder messages on screen.
Use
/
to select your desired setting.
Splash Screen
in the
Advanced menu
>
System Setup: Basic
menu sets a
preferred logo screen to be displayed during projector start-up. Use
/
to
select a screen.
Select the lamp saver mode
1.
Open the OSD menu and go to the
Advanced menu
>
Picture
>
Lamp
Power
menu.
2.
Press
/
to select Normal
/
Economic
/
SmartEco. The lamp brightness vary
from the different lamp mode,see the description list in table below.
If the Economic mode or SmartEco mode is selected, the light output will be
reduced and result in darker projected pictures.
Lamp Power
Description
Normal
Provides full lamp brightness
Economic
Lower brightness to extend the lamp life and decreases the fan
noise
SmartEco
Adjusts the lamp power automatically depending on the
content brightness level