Bissell ProHeat 2X Upright Carpet Cleaner 1383 User Guide - Page 11

Cleaning with the Stain Trapper Tool

Get Bissell ProHeat 2X Upright Carpet Cleaner 1383 PDF manuals and user guides View all Bissell ProHeat 2X Upright Carpet Cleaner 1383 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Operations and residue that can be accessed before deep cleaning. 4. Be sure to test any spot removal formulas in an inconspicuous area first. This is important as some dyes and materials could be damaged or discolored by cleaning solvents. If such a change should occur, try a different solution or call a professional. 5. If cleaning on Berber carpeting, gently run your machine over a hidden area. If no fuzzing occurs, continue cleaning in soiled area. 6. Using the BISSELL Stain PreTreat, spray evenly over soiled area. Do not overwet. Wait 3-5 minutes. Gently work the solution by blotting area with a clean, damp, color safe cloth. 7. Clean using either the FLOOR CLEANING, or TOOLS setting on the ReadyTools dial. Cleaning with the Stain Trapper Tool 1. Follow steps 1-5 on page 9. 2. Gently scrape up any semi-solids with a spoon or spatula. Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery. 3. Plug in and turn on the power switch. 4. Clean by pressing the trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the trigger to suction soiled water. Continue to clean in the area, working in small sections, until no more dirt can be removed. Rinse (optional) and suction as needed. CAUTION: Do not overwet. NOTE: Do not fill the Stain Trapper tank above the FULL line. 5. To empty the Stain Trapper tool, rotate 5. the small tank on the bottom of the tool to unlock it. NOTE: Be careful to keep the top of the tool facing upward or soiled water will spill out of the tank. 6. Dump dirty water into a sink or toilet and rinse the tank out with clean water. Replace the tank by lining up the "unlock" symbol with the small arrow on the tank and turning it to 7. the "lock" symbol. 7. Clean the front of the tool by removing the plate over the suction path. Pull down on the bottom of the plate to remove. Run the tool and the plate under clean water to rinse taking care to remove all debris. Replace the front plate by sliding it back into place. www.bissell.com 800.237.7691 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Operati´s
and residue that can be accessed before deep
cleaning.
4.
Be sure to test any spot removal formulas in
an inconspicuous area first. This is important as
some dyes and materials could be damaged or
discolored by cleaning solvents. If such a change
should occur, try a different solution or call a
professional.
5.
If cleaning on Berber carpeting, gently run
your machine over a hidden area.
If no fuzzing occurs, continue cleaning
in soiled area.
6.
Using the BISSELL Stain PreTreat, spray
evenly over soiled area. Do not overwet. Wait
3-5 minutes. Gently work the solution by blotting
area with a clean, damp, color safe cloth.
7.
Clean using either the FLOOR CLEANING, or
TOOLS setting on the ReadyTools dial.
Cleaning with the Stain Trapper Tool
1.
Follow steps 1-5 on page 9.
2.
Gently scrape up any semi-solids with a spoon
or spatula. Do not use a knife or other utensil
with sharp edges because it could damage the
carpet or upholstery.
3.
Plug in and turn on the power switch.
4.
Clean by pressing the trigger to spray solu-
tion onto the area to be cleaned. Slowly move
the tool back and forth over the soiled surface.
Release the trigger to suction soiled water.
Continue to clean in the area, working in small
sections, until no more dirt can be removed.
Rinse (optional) and suction as needed.
CAUTION: Do not overwet.
NOTE: Do not fill the Stain Trapper tank
above the FULL line.
5.
To empty the Stain Trapper tool, rotate
the small tank on the bottom of the tool
to unlock it.
NOTE: Be careful to keep the top of the tool
facing upward or soiled water will spill out of
the tank.
6.
Dump dirty water into a sink or toilet and
rinse the tank out with clean water. Replace
the tank by lining up the “unlock” symbol with
the small arrow on the tank and turning it to
the “lock” symbol.
7.
Clean the front of the tool by removing the
plate over the suction path. Pull down on the
bottom of the plate to remove. Run the tool
and the plate under clean water to rinse taking
care to remove all debris. Replace the front
plate by sliding it back into place.
www.BISSELL.com
800.237.7691
11
7.
5.