Bosch SHX68E15UC Instructions for Use - Page 15

Operating the Unit

Get Bosch SHX68E15UC - 24inch Evolution 800 PDF manuals and user guides
UPC - 825225868781
View all Bosch SHX68E15UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Delay start You can delay the start of the program in 1-hour steps up to 24 hours. • Open the door (for hidden controls only). Turn unit on using the ON/OFF button. • Press "+" button until the timer programming display jumps to 01 . • Press + or - button until the displayed time corresponds with your requirements. • Press START button. Delay start is activated. To cancel delay start: • Press the + or - button until "00" is indicated on the digital display. You can change your program selection at any time until the program starts. • Close the door (for hidden controls only). Cycle Completion Signal The cycle completion is also indicated by a tone.This function can be changed as follows: • Open the door (for hidden controls only). Turn unit on using the ON/OFF button. • Hold down "A" button and press START button until the display shows H:00. • Release both buttons. • Press "A" until the display shows "b:02". • Press "C" to increase or decrease the tone. • b:00 = Off and b:03 = loudest • Press START to save the setting. Intensive drying The inal rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) • Open the door. (for hidden controls only). Turn unit on using the ON/OFF button. Hold down "A" button and press START the digital display shows "H:00". • Release both buttons. • Press button "A" until the display indicates "d:00" To change the setting, • Press button "C" (see page 4) to turn intensive drying ON = d:01 or OFF = d:00 • Press START button. The set value is saved. • Close the door (for hidden controls only). Operating the Unit Switching on the appliance • For hidden controls, open the door. • Turn unit on by pressing the ON/OFF switch. The display of the last selected program lashes. • The expected program duration lashes on the digital display. • Press the START button. • Close the door. The program starts running. Interrupting the cycle • Open the door (for hidden controls only). • Press the ON/OFF button. The LEDs go out. The program is saved. If the door was opened on an appliance which has a warm water connection or is heated, irst leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. • To continue the program, switch on the ON/OFF switch again. • Close the door. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Delay start
You can delay the start of the program in 1-hour steps up to 24 hours.
Open the door
•
(for hidden controls only). Turn unit on using the ON/OFF button.
Press “
•
+
” button until the timer programming display jumps to 01 .
Press + or – button until the displayed time corresponds with your requirements.
•
Press START button. Delay start is activated.
•
To cancel delay start:
Press the + or – button until “00” is indicated on the digital display.
•
You can change your program selection at any time until the program starts.
Close the door
•
(for hidden controls only).
Cycle Completion Signal
The cycle completion is also indicated by a tone.This function can be changed as
follows:
Open the door
•
(for hidden controls only). Turn unit on using the ON/OFF button.
Hold down “
•
A
” button and press START button until the display shows H:00.
Release both buttons.
•
Press “
•
A
” until the display shows “
b:02
”.
Press “
•
C
” to increase or decrease the tone.
b:00
•
= Off and
b:03
= loudest
Press
•
START
to save the setting.
±ntensive drying
The Inal rinse uses a higher temperature which improves the drying result.
The running time may increase slightly. (Caution if utensils are delicate!)
Open the door.
•
(for hidden controls only). Turn unit on using the ON/OFF button.
Hold down “
A
” button and press START the digital display shows “H:00”.
Release both buttons.
•
Press button “A” until the display indicates “d:00”
•
To change the setting,
Press button “C” (see page 4) to turn intensive drying ON = d:01 or OFF = d:00
•
Press START button. The set value is saved.
•
Close the door
•
(for hidden controls only).
±nterrupting the cycle
Open the door
•
(for hidden controls only).
Press the ON/OFF button. The LEDs go out. The program is saved. If the door
•
was opened on an appliance which has a warm water connection or is heated,
Irst leave the door ajar for several minutes and then close. Otherwise, expansion
(pressure) may cause the appliance door to spring open or water to run out of
the appliance.
To continue the program, switch on the ON/OFF switch again.
•
Close the door.
•
Operating the Unit
Switching on the appliance
For hidden controls, open the door.
•
Turn unit on by pressing the ON/OFF switch. The display of the last
•
selected program ±ashes.
The expected program duration ±ashes on the digital display.
•
Press the START button.
•
Close the door. The program starts running.
•
15