Bosch VDC-455V04-20S Installation Instructions - Page 22

Installer Settings

Page 22 highlights

FlexiDomeXT+ | Installation Manual EN | 22 Installer Settings Install menu Function Selection SET FOCUS NOW COMM ON, OFF HEATER AUTO, OFF DEFAULTS Select submenu EXIT Description Forces the lens to fully open the iris. Adjust the lens focus now. Bilinx communication ON/OFF Select AUTO to enable the thermostatically controlled heater function Return all settings for all modes to factory defaults Exit the menu Adjustment procedure DC-iris Lens: 1. Unlock the focus locking screw. 2. SET BACK FOCUS NOW is highlighted in the menu. 3. Turn the focus adjustment as required. 4. Lock the focus locking screw. 5. Exit the menu selection. Defaults submenu Function ALL DEFAULTS Selection EXIT Description Select to restore the factory defaults. A confirmation screen appears. Allow 5 seconds for the camera to optimize the picture after a mode reset. Exit the menu Camera control communication This camera is equipped with a coaxial communications transceiver. In combination with VP-CFGSFT, the camera can be adjusted from the headend side of the coaxial cable. All menus can be accessed remotely giving full control of the camera. With this communication it is also possible to disable the local keys on the camera. To avoid loss of communication on an installed camera, the Communication ON/OFF selection is not available while using remote control. This function can only be accessed with the camera buttons. Bosch Security Systems | 2008-08 | V1.1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210

FlexiDome
XT+
| Installation Manual
Bosch Security Systems | 2008-08 | V1.1
EN | 22
Installer Settings
Install menu
Adjustment procedure DC-iris Lens:
1.
Unlock the focus locking screw.
2.
SET BACK FOCUS NOW is highlighted in the menu.
3.
Turn the focus adjustment as required.
4.
Lock the focus locking screw.
5.
Exit the menu selection.
Defaults submenu
Camera control communication
This camera is equipped with a coaxial communications transceiver. In
combination with VP-CFGSFT, the camera can be adjusted from the head-
end side of the coaxial cable. All menus can be accessed remotely giving
full control of the camera. With this communication it is also possible to
disable the local keys on the camera. To avoid loss of communication on
an installed camera, the Communication ON/OFF selection is
not
available while using remote control. This function can only be accessed
with the camera buttons.
Function
Selection
Description
SET FOCUS
NOW
Forces the lens to fully open the iris. Adjust the
lens focus now.
COMM
ON, OFF
Bilinx communication ON/OFF
HEATER
AUTO, OFF
Select AUTO to enable the thermostatically
controlled heater function
DEFAULTS
Select submenu
Return all settings for all modes to factory
defaults
EXIT
Exit the menu
Function
Selection
Description
ALL
DEFAULTS
Select to restore the factory defaults. A confirmation
screen appears. Allow 5 seconds for the camera to
optimize the picture after a mode reset.
EXIT
Exit the menu