Bosch VJT-X10S Operation Manual - Page 81

Advanced Mode: Multicasting, SNMP host address / 2. SNMP host address, SNMP traps, Select

Get Bosch VJT-X10S PDF manuals and user guides View all Bosch VJT-X10S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

VideoJet X10 5.40 Configuration Using a Web Browser | en 81 If you select On for the SNMP parameter and do not enter an SNMP host address, the VideoJet X10 does not send them automatically, but only replies to SNMP requests. If you enter one or two SNMP host addresses, SNMP traps are sent automatically. Select Off to deactivate the SNMP function. 1. SNMP host address / 2. SNMP host address If you wish to send SNMP traps automatically, enter the IP addresses of one or two required target units here. SNMP traps You can select which traps are to be sent. 1. Click Select. A list is opened. 2. Click the checkboxes to select the required traps. All the checked traps will be sent. 3. Click Set to accept the selection. Authentication If a RADIUS server is employed in the network for managing access rights, authentication must be activated here to allow communication with the unit. The RADIUS server must also contain the corresponding data. To configure the unit, you must connect the VideoJet X10 directly to a computer using a network cable. This is because communication via the network is not enabled until the Identity and Password parameters have been set and successfully authenticated. Identity Enter the name that the RADIUS server is to use for identifying the VideoJet X10. Password Enter the password that is stored in the RADIUS server. RTSP port If necessary, select a different port for the exchange of the RTSP data from the list. The standard RTSP port is 554. Select Off to deactivate the RTSP function. Advanced Mode: Multicasting In addition to a 1:1 connection between an encoder and a single receiver (unicast), the VideoJet X10 can enable multiple receivers to receive the video signal from an encoder simultaneously. The device either duplicates the data stream itself and then distributes it to multiple receivers (Multi-unicast) or it sends a single data stream to the network, where the data stream is simultaneously distributed to multiple receivers in a defined group (Multicast). Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
VideoJet X10
Configuration Using a Web Browser | en
81
Bosch Security Systems
Installation and Operating Manual
DOC | V4.0 | 2009.06
If you select
On
for the
SNMP
parameter and do not enter an SNMP host address, the
VideoJet X10 does not send them automatically, but only replies to SNMP requests. If you
enter one or two SNMP host addresses, SNMP traps are sent automatically. Select
Off
to
deactivate the SNMP function.
1. SNMP host address / 2. SNMP host address
If you wish to send SNMP traps automatically, enter the IP addresses of one or two required
target units here.
SNMP traps
You can select which traps are to be sent.
1.
Click
Select
. A list is opened.
2.
Click the checkboxes to select the required traps. All the checked traps will be sent.
3.
Click
Set
to accept the selection.
Authentication
If a RADIUS server is employed in the network for managing access rights, authentication
must be activated here to allow communication with the unit. The RADIUS server must also
contain the corresponding data.
To configure the unit, you must connect the VideoJet X10 directly to a computer using a
network cable. This is because communication via the network is not enabled until the
Identity
and
Password
parameters have been set and successfully authenticated.
Identity
Enter the name that the RADIUS server is to use for identifying the VideoJet X10.
Password
Enter the password that is stored in the RADIUS server.
RTSP port
If necessary, select a different port for the exchange of the RTSP data from the list. The
standard RTSP port is 554. Select
Off
to deactivate the RTSP function.
5.40
Advanced Mode: Multicasting
In addition to a 1:1 connection between an encoder and a single receiver (unicast), the
VideoJet X10 can enable multiple receivers to receive the video signal from an encoder
simultaneously. The device either duplicates the data stream itself and then distributes it to
multiple receivers (Multi-unicast) or it sends a single data stream to the network, where the
data stream is simultaneously distributed to multiple receivers in a defined group (Multicast).