Bosch WTB86200UC Instructions for Use - Page 21

Before using the dryer for the first time, Temporary disconnection of the dryer, Using the program

Page 21 highlights

@ Lint filter H Air inlet P Open the maintenance flap Heat exchanger Close the maintenance flap 9 WARNING BEFORE INSTALLING OR USING YOUR DRYER Read and follow all installation and operating instructions. Check the machine. Never start a damaged machine! Contact your customer service! ~ Customer service; Page 4 Check to be sure your household electrical system voltage and the voltage specifications on the dryer rating plate correspond. Check to be sure the dryer drain hose is installed properly. Turning the dryer on and off The rotating Program Selector turns the dryer on as drying cycle is selected and off when the selector is later turned to the vertical Off position. Before using the dryer for the first time 1. Read these operating instructions carefully. 2. Check that the supply voltage corresponds with the voltage specifications on the rating plate on the dryer, see top rear side of the dryer and/or rating plate label inside of the dryer door. 3. Remove all objects from the drum. 4. Check the dryer for visible damage. If damage found contact your dealer. 5. Wipe the inside of the drum with a damp cloth. 6. Check heating system. ~ Check heating system; Page 15 7. If the dryer does not work, switch the dryer to Off. Look in the Troubleshooting section of the operating instructions and find the fault. ~ Troubleshooting; Page 28 Temporary disconnection of the dryer Operate your dryer only when you are at home. If you intend going on vacation or are not using your dryer for an extended period of time, you should: 1. Turn off the circuit breaker. 2. Pull out the power supply plug if possible. 3. Clean the lint filter. Using the program selector to choose a drying cycle NOTICE: If you have activated the childproof lock, you must deactivate it before you can set a program. Use the program selector to select the desired drying cycle. Turns in both directions. The machine is switched on. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

21
9
WARNING
BEFORE INSTALLING OR USING YOUR DRYER
Read and follow all installation and operating
instructions.
Check the machine. Never start a damaged machine!
Contact your customer service!
~
Customer service; Page 4
Check to be sure your household electrical system
voltage and the voltage specifications on the dryer rating
plate correspond.
Check to be sure the dryer drain hose is installed
properly.
Turning the dryer on and off
The rotating Program Selector turns the dryer on as
drying cycle is selected and off when the selector is later
turned to the vertical
Off
position.
Before using the dryer for the first time
1.
Read these operating instructions carefully.
2.
Check that the supply voltage corresponds with the
voltage specifications on the rating plate on the dryer,
see top rear side of the dryer and/or rating plate label
inside of the dryer door.
3.
Remove all objects from the drum.
4.
Check the dryer for visible damage. If damage found
contact your dealer.
5.
Wipe the inside of the drum with a damp cloth.
6.
Check heating system.
~
Check heating system; Page 15
7.
If the dryer does not work, switch the dryer to
Off
.
Look in the Troubleshooting section of the operating
instructions and find the fault.
~
Troubleshooting; Page 28
Temporary disconnection of the dryer
Operate your dryer only when you are at home. If you
intend going on vacation or are not using your dryer for
an extended period of time, you should:
1.
Turn off the circuit breaker.
2.
Pull out the power supply plug if possible.
3.
Clean the lint filter.
Using the program selector to choose a
drying cycle
NOTICE:
If you have activated the childproof lock, you
must deactivate it before you can set a program.
Use the program selector to select the desired drying
cycle. Turns in both directions.
The machine is switched on.
@
Lint filter
H
Air inlet
P
Open the maintenance flap
Close the maintenance flap
Heat exchanger