Bosch WTMC5521UC Operating, Care, Installation (all languages) - Page 9
Attention - lp kit
View all Bosch WTMC5521UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
LP - Gas Kit part no. WTZ1280 The parts required for the LP version can be obtained from your local dealer. Please follow the installation instructions supplied by the appropriate manufacturer! If you have a propane gas dryer and need to convert it to natural gas, (Service Kit 496297) please consult your customer service agent for assistance. Note: Dryer must be checked for proper operation whenever the gas connections have been broken. Bottom exhaust kit part no. WTZ1270 Note: The maximum permitted number of 90° elbows (including this side exhaust kit) is four! Dryer rack part no. WTZ 1290 Use the dryer rack to dry washable woolen textiles (e.g. sweaters) and shoes. Left hinge kit part no. WTZ 1260 for all dryers except silver and duo tone silver part no. WTZ 126S for silver and duo tone silver dryers The door catch can be reversed if necessary. The door is hinged on the right at the factory. Pedestal Mounting Kit part no. WTZ 1295 (White Dryers) part no. WTZ 1295S (Silver Dryers) part. no. WTZ 1295P (Duo tone Silver) part. no. WTZ 1295R (Duo tone Red) If mounting the dryer on the pedestal follow the instructions supplied with the pedestal. Mobile home kit part no. WTZ 1275 Note: Please check with the Authority Having Jurisdiction in your area to verify if a gas dryer can be installed in your mobile home. Once that has been verified, installation of the dryer shall conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)}, and/or Standard CAN/CSAĆZ240 MH. Please use mobile home kit number WTZ 1275 for means to secure the dryer to the structure. See page 9 Exhaust Air Connection" for the exhaust duct installation instructions. The exhaust duct must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. An opening to the outside must be provided during installation. Insure that the free area of the opening for the introduction of outside air is not less than twice the area of the dryer exhaust outlet or use at least a 5 inch diameter exhaust or at least a 25 in2 square exhaust duct for the opening. Installation ć step by step 1. Unpack the dryer. 2. Remove all objects from the drum. 3. Check the dryer for visible damage. 4. Position the dryer near the installation location. 5. If required, have customer service change the door hinges to the left (see page 6). 6. If required, have customer service install the exhaust air outlet on the dryer (see page 7). 7. Have the gas supply connected by an qualified technician (see page 7). 8. Install exhaust duct, if necessary. Follow the installation instructions supplied by the appropriate manufacturer! i If space is very restricted, it is recommended to fit the initial parts of the exhaust duct to the dryer before the dryer is moved to its final installation location. 9. Move the dryer to its final location and align. ATTENTION Do not slide dryer across the floor if heightĆadjustable feet have been extended. Feet and/or dryer base may be damaged if dryer is slid across floor with heightĆadjustable feet extended. 10. Position and then level the dryer. The dryer should be level with all four feet firmly on the ground. The dryer must not wobble. If the dryer is not level or if it does wobble, the feet must be adjusted. Adjust the heightĆadjustable feet until the dryer does not rock and is level, both frontĆtoĆback and sideĆtoĆside. 11. Connect the exhaust duct to the exhaust air outlet on the dryer. 12. Insert plug into the wall receptacle. 9