Brother International BAS-300A Application Instruction Manual - English - Page 14

operation.

Get Brother International BAS-300A PDF manuals and user guides View all Brother International BAS-300A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

El To program an intermittent stitch sewing operation • After the thread trimming operation is completed, if the sewing operation is to be continued without lifting the work clamp, use the FE) key (Feed key) to facilitate the programming operation. (X-0 • V-0) Example: Program the pattern in the figure at left. (1) Press the E key. The work clamp will move to the point of origin (X-0; Y-0), the numeral "0" will be indicated on the STEP display, and the command indicator "F" will illuminate. (2) Operate the direction keys to move the work clamp to the initial stitch position. (3) When the tip of the needle and the initial stitch position ® on the outline of the needle movement become aligned, press the key. Thus, the initial stitch will be programmed. (4) Repeat the above procedure to program the remaining stitches of pattern 1. (5) Press the key at the final stitch position of ® pattern 1, and then press the El key. At this time, the command indicator "F" will illuminate. Pattern 1 /- Feed key Pattern 1 Pattern 2 • ^111^ (6) Operate the direction keys to move the work clamp to the initial stitch position of pattern 2. (7) When the tip of the needle and the initial stitch position of pattern 2 become aligned, press the E key. Thus, the operation will be programmed to restart from point after the thread trimming operation is completed at point S. (8) Repeat the above procedure to program the remaining stitches of pattern 2. (9) Press the key at the final stitch position 0, and press the numeral key O 3 times to indicate "111" on the STEP display. Then, press the El key. (10) The work clamp will move back to the initial stitch position. (11) Press the program R/W switch to write the pattern to disk. (Refer to page 24.) Pattern 2 N._ -11-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
El
To
program
an
intermittent
stitch
sewing
operation
•
After
the
thread
trimming
operation
is
completed,
if
the
sewing
operation
is
to
be
continued
without
lifting
the
work
clamp,
use
the
FE)
key
(Feed
key)
to
facilitate
the
programming
operation.
(X-0
•
V-0)
Pattern
1
/-
Pattern
1
Feed
key
Pattern
2
N._
•
^111^
Pattern
2
Example:
Program
the
pattern
in
the
figure
at
left.
(1)
Press
the
E
key.
The
work
clamp
will
move
to
the
point
of
origin
(X-0;
Y-0),
the
numeral
"0"
will
be
indicated
on
the
STEP
display,
and
the
command
indicator
"F"
will
illuminate.
(2)
Operate
the
direction
keys
to
move
the
work
clamp
to
the
initial
stitch
position.
(3)
When
the
tip
of
the
needle
and
the
initial
stitch
position
®
on
the
outline
of
the
needle
movement
become
aligned,
press
the
key.
Thus,
the
initial
stitch
will
be
programmed.
(4)
Repeat
the
above
procedure
to
program
the
remaining
stitches
of
pattern
1.
(5)
Press
the
key
at
the
final
stitch
position
of
pattern
1,
and
then
press
the
El
key.
At
this
time,
the
command
indicator
"F"
will
illuminate.
(6)
Operate
the
direction
keys
to
move
the
work
clamp
to
the
initial
stitch
position
of
pattern
2.
(7)
When
the
tip
of
the
needle
and
the
initial
stitch
position
of
pattern
2
become
aligned,
press
the
E
key.
Thus,
the
operation
will
be
programmed
to
restart
from
point
after
the
thread
trimming
operation
is
completed
at
point
S.
(8)
Repeat
the
above
procedure
to
program
the
remaining
stitches
of
pattern
2.
(9)
Press
the
key
at
the
final
stitch
position
0,
and
press
the
numeral
key
O
3
times
to
indicate
"111"
on
the
STEP
display.
Then,
press
the
El
key.
(10)
The
work
clamp
will
move
back
to
the
initial
stitch
position.
(11)
Press
the
program
R/W
switch
to
write
the
pattern
to
disk.
(Refer
to
page
24.)
—11—