Brother International TD-2135N Users Guide TD-2020A/2125NWB/2135NWB - Page 15

Checking the Sensor Position, d

Get Brother International TD-2135N PDF manuals and user guides View all Brother International TD-2135N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

2 Feed the end of the fanfold paper under the media tip guides (1). 1 3 Position the end of the paper centered over the platen roller and slightly out of the media exit. 4 Close the Media Roll compartment top cover by pressing it in the center. Press down until it locks into place. Printing d Press the (Power) button to turn the printer on. NOTE If the paper size information for the die-cut labels being used has been registered 2 with the printer, pressing the (Feed) button will position the label at the correct starting position. For more information, see Registering Paper Size Information With the Printer on page 4. Checking the Sensor Position 2 Check the sensor position for the type of paper being used.  With die-cut labels that have no black mark, the transmissive/gap sensor detects the beginning of the label and feeds the label to the correct position.  With receipt paper that has no black mark, the reflective/black mark sensor detects if paper has run out.  With media that has a black mark, the reflective/black mark sensor detects the mark and feeds the media to the correct position. With no black mark  Die-cut labels Align on the sensor with on the printer. (See Figure 1.)  Receipt paper Width of 0.985" Align on the sensor with (25 mm) or more on the printer. (See Figure 1.) Width less than Align on the sensor with 0.985" (25 mm) on the printer. (See Figure 2.) With a black mark Align the black mark on the paper with the centerline of the reflective/black mark sensor. (See Figure 3.) Make sure that there is at least 0.16" (4 mm) of the black mark on the left and right of the centerline for the reflective/black mark sensor. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Printing
9
2
2
Feed the end of the fanfold
paper under the media tip
guides (1).
3
Position the end of the paper
centered over the platen roller
and slightly out of the media
exit.
4
Close the Media Roll
compartment top cover by
pressing it in the center.
Press down until it locks into
place.
d
Press the
(Power) button to turn the
printer on.
NOTE
If the paper size information for the die-cut
labels being used has been registered
with the printer, pressing the
(Feed)
button will position the label at the correct
starting position. For more information,
see
Registering Paper Size Information
With the Printer
on page 4.
Checking the Sensor Position
2
Check the sensor position for the type of
paper being used.
With die-cut labels that have no black
mark, the transmissive/gap sensor
detects the beginning of the label and
feeds the label to the correct position.
With receipt paper that has no black mark,
the reflective/black mark sensor detects if
paper has run out.
With media that has a black mark, the
reflective/black mark sensor detects the
mark and feeds the media to the correct
position.
1
With no black mark
Die-cut labels
Align
on the sensor with
on the printer.
(See
Figure 1
.)
Receipt paper
Width of 0.985"
(25 mm) or more
Align
on the sensor with
on the printer. (See
Figure 1
.)
Width less than
0.985" (25 mm)
Align
on the sensor with
on the printer. (See
Figure 2
.)
With a black mark
Align the black mark on the paper with the
centerline of the reflective/black mark sensor.
(See
Figure 3
.)
Make sure that there is at least 0.16" (4 mm) of
the black mark on the left and right of the
centerline for the reflective/black mark sensor.