Brother International XL-2230 Users Manual - English - Page 22

Lower Threading For One-touch, lower threading - model

Get Brother International XL-2230 PDF manuals and user guides View all Brother International XL-2230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Replace the bobbin cover. Put the left tab in 5 place (see arrow 1), and then press lightly on the right side (see arrow 2) until the cover clicks into place. Lower Threading (For One-touch lower threading) This is only available on certain models. 1 2 CAUTION ● Setting the bobbin improperly may cause the thread tension to loosen, breaking the needle 1 and resulting in injury. • Replace the cover so that the end of the thread comes out from the left side of the cover (as shown by the line in the diagram). 1 2 1 Wound evenly 2 Wound poorly ● The bobbin was designed specifically for this sewing machine. If bobbins from older models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, SFB (XA5539-151)). Actual size 11.5 mm (7/16 inch) This model Older model CAUTION ● Be sure to turn off the power. If you accidentally step on the foot controller and the machine begins to operate, injury could result. Raise the needle to its highest position by 1 turning the balance wheel toward you (counterclockwise) and raise the presser foot lever. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
21
1
5
Replace the bobbin cover. Put the left tab in
place (see arrow
1
), and then press lightly on
the right side (see arrow
2
) until the cover
clicks into place.
• Replace the cover so that the end of the
thread comes out from the left side of the
cover (as shown by the line in the diagram).
Lower Threading (For One-touch
lower threading)
This is only available on certain models.
1
Raise the needle to its highest position by
turning the balance wheel toward you
(counterclockwise) and raise the presser foot
lever.
2
1
●
Setting the bobbin improperly may cause the
thread tension to loosen, breaking the needle
and resulting in injury.
1
Wound evenly
2
Wound poorly
●
The bobbin was designed specifically for
this sewing machine. If bobbins from older
models are used, the machine will not
operate correctly. Use only the enclosed
bobbin or bobbins of the same type
(part code: SA156, SFB (XA5539-151)).
●
Be sure to turn off the power. If you
accidentally step on the foot controller
and the machine begins to operate, injury
could result.
CAUTION
1
2
Actual size
This model
Older model
11.5 mm
(7/16 inch)
CAUTION