Canon VIXIA HF G60 Instruction Manual - Page 36

During record, tandby mode, touch [PHOTO

Get Canon VIXIA HF G60 PDF manuals and user guides View all Canon VIXIA HF G60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Recording Video and Photos To take photos 4 During record standby mode, touch [PHOTO]. • By default, the [ Photo] function is assigned to the onscreen assignable button, but you can change 36 the assigned function if necessary (A 84). • A green g icon will appear at the bottom of the screen. Also, at the upper right of the screen, {Ð will appear with the icon of the card selected for recording photos. • You can also press the PHOTO button on the supplied wireless controller. When you have finished recording 1 Set the lens barrier switch to CLOSED to close the lens barrier. 2 Make sure that the ACCESS indicator is off. 3 Set the power switch to OFF. 4 Close the LCD panel and return the viewfinder to its retracted position. IMPORTANT • Be sure to save your recordings regularly (A 99), especially after making important recordings. Canon shall not be liable for any loss or corruption of data. NOTES • The maximum continuous recording time of a single clip is 6 hours. After that, a new clip will be created automatically and recording will continue as a separate clip. • When recording in bright places, it may be difficult to use the LCD screen. In such case, use the viewfinder or adjust the brightness of the screen (A 21). • A video recording will be saved as separate clips in the following cases: - When the camcorder switches to the other SD card while recording video due to the relay recording function (A 33). - When recording clips on an SDHC card, the video (stream) file in the clip will be split approximately every 4 GB. Playback with the camcorder will be continuous. After saving the separate split clips to a computer, you can use MP4 Join Tool to join the files and save them as a single clip (A 99). • About the power saving mode: When > [B System Setup] > [Auto Power Off] is set to [i On], the camcorder will shut off automatically to save power when it is powered by a battery pack and is left without any operation for 5 minutes. Use the power switch to turn on the camcorder. • Recording photos: - Photos are recorded as JPG files. Photos can be recorded only in record standby mode. - Photos cannot be recorded when pre-recording is activated. • When you need to record for a long time with the camcorder set on a tripod, you can close the LCD panel and use only the viewfinder in order to save power when using a battery pack (A 21).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Recording Video and Photo
s
36
To ta
k
e photo
s
4 During record
s
tandby mode, touch [PHOTO].
•
By default, the [
Photo] function is assigned to the onscreen assignable button, but you can change
the assigned function if necessary (
A
84).
•
A green
g
icon will appear at the bottom of the screen. Also, at the upper right of the screen,
{Ð
will
appear with the icon of the card selected for recording photos.
•
You can also press the PHOTO button on the supplied wireless controller.
When you have fini
s
hed recording
1
Set the lens barrier switch to CLOSED to close the lens barrier.
2
Make sure that the ACCESS indicator is off.
3
Set the power switch to OFF.
4
Close the LCD panel and return the viewfinder to its retracted position.
IMPORTANT
•
Be sure to save your recordings regularly (
A
99), especially after making important recordings. Canon shall
not be liable for any loss or corruption of data.
NOTES
NOTES
•
The maximum continuous recording time of a single clip is 6 hours. After that, a new clip will be created
automatically and recording will continue as a separate clip.
•
When recording in bright places, it may be difficult to use the LCD screen. In such case, use the viewfinder or
adjust the brightness of the screen (
A
21).
•
A video recording will be saved as separate clips in the following cases:
-
When the camcorder switches to the other SD card while recording video due to the relay recording function
(
A
33).
-
When recording clips on an SDHC card, the video (stream) file in the clip will be split approximately every
4 GB. Playback with the camcorder will be continuous.
After saving the separate split clips to a computer, you can use
MP4 Join Tool
to join the files and save them
as a single clip (
A
99).
•
About the power saving mode:
When
>
[
B
System Setup]
>
[Auto Power Off] is set to [
i
On],
the camcorder will shut off automatically to save power when it is powered by a battery pack and is left without
any operation for 5 minutes. Use the power switch to turn on the camcorder.
•
Recording photos:
-
Photos are recorded as JPG files. Photos can be recorded only in record standby mode.
-
Photos cannot be recorded when pre-recording is activated.
•
When you need to record for a long time with the camcorder set on a tripod, you can close the LCD panel and
use only the viewfinder in order to save power when using a battery pack (
A
21).