Canon imageFORMULA DR-5080C High Speed Color Instruction Manual - Page 65

Setting in the User Mode

Get Canon imageFORMULA DR-5080C High Speed Color PDF manuals and user guides View all Canon imageFORMULA DR-5080C High Speed Color manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Chapter 3 Preparing Documents Setting in the User Mode The DR-5020/5080C allows you to select which operation mode (user mode) is used for each of the items below. (Settings U5 to U9 are available only when the corresponding optional device (imprinter, bar code decoder or endorser) is attached.) Energy-saveing mode setting U0-0 Do not go into energy-saving mode. U0-1 Go into energy-saving mode after 15 minutes of no operation. (default) Operation panel buzzer setting U1-0 Do not sound buzzer during key operation. U1-1 Sound buzzer during key operation. (default) Document detection setting U2-0 Detect document width by document width. U2-1 Detect document width by paper guide width. (default) U3-0 U3-1 U3-2 Do not detect document skew. (default) Detect document skew and stop scanning. Detect document skew and stop scanning. (excluding manual mode) SCSI synchronization setting U4-0 Do not transfer SCSI synchronization. U4-1 Transfer SCSI synchronization. (default) Bar code setting U5-0 Do not sound buzzer during bar code reading. U5-1 Sound buzzer during bar code reading. (default) U6-0 Output START/STOP codes in Codabar bar code in lower case. (default) U6-1 Output START/STOP codes in Codabar bar code in upper case. U7-0 U7-1 U7-2 U7-3 Do not verify bar code. Verify bar code once. (default) Verify bar code twice. Verify bar code three times. Count Only mode setting U8-0 Do not use imprinter/endorser in Count Only mode. (default) U8-1 Use imprinter/endorser in Count Only mode. Endorser stamp mode setting U9-0 Use the endorser in the check mode. (default). U9-1 Use the endorser in the A4 mode. 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
64
Chapter 3
Preparing Documents
Setting in the User Mode
The DR-5020/5080C allows you to select which operation mode (user mode) is
used for each of the items below.
(Settings U5 to U9 are available only when the corresponding optional device
(imprinter, bar code decoder or endorser) is attached.)
Energy-saveing mode setting
U0-0
Do not go into energy-saving mode.
U0-1
Go into energy-saving mode after 15 minutes of no
operation. (default)
Operation panel buzzer setting
U1-0
Do not sound buzzer during key operation.
U1-1
Sound buzzer during key operation. (default)
Document detection setting
U2-0
Detect document width by document width.
U2-1
Detect document width by paper guide width. (default)
U3-0
Do not detect document skew. (default)
U3-1
Detect document skew and stop scanning.
U3-2
Detect document skew and stop scanning. (excluding manual mode)
SCSI synchronization setting
U4-0
Do not transfer SCSI synchronization.
U4-1
Transfer SCSI synchronization. (default)
Bar code setting
U5-0
Do not sound buzzer during bar code reading.
U5-1
Sound buzzer during bar code reading. (default)
U6-0
Output START/STOP codes in Codabar bar code in lower case. (default)
U6-1
Output START/STOP codes in Codabar bar code in upper case.
U7-0
Do not verify bar code.
U7-1
Verify bar code once. (default)
U7-2
Verify bar code twice.
U7-3
Verify bar code three times.
Count Only mode setting
U8-0
Do not use imprinter/endorser in Count Only mode. (default)
U8-1
Use imprinter/endorser in Count Only mode.
Endorser stamp mode setting
U9-0
Use the endorser in the check mode. (default).
U9-1
Use the endorser in the A4 mode.