Carvin DCM2000LX Instruction Manual - Page 22

C Router Matrix, D Frequency Chart

Get Carvin DCM2000LX PDF manuals and user guides View all Carvin DCM2000LX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

6.C ROUTER (MATRIX) (middle left screen) 6.C.1 BRIDGE CHANNELS BRIDGE 1-2, (3-4) button(s) combine amps 1 & 2 (or 3 & 4) for a single high power output. Use the appropriate output jacks when bridging amps. *Note: the minimum impedance for a BRIDGED output is 4 ohms for 2 channel amps, and 8 ohms for the DCM2004Lx. 6.C.2 OUTPUT MUTES Click the MUTE buttons to mute or un-mute each output. 6.C.3 ROUTING INPUT SOURCES TO OUTPUTS Click the A, B, ( C, D ) buttons select the signal source(s) for each output. 6.C.4 OUTPUT NAME Click in the "Output 1" (etc.) box to type a new name for each output. 6.D FREQUENCY CHART (middle right screen) 6.D.1 OUTPUT DISPLAY BUTTONS 1, 2 (3, 4) Displays the frequency response of each amp output as a different color. 6.D.2 ADJUSTING PEQs FROM THE FREQUENCY CHART The Parametric EQs can be manipulated directly from the Frequency Chart. Highlight the curve from the lower OUTPUT section with the blue OUTPUT select 1, 2, (3, 4) buttons. (see 6.E.2) Click and drag a round node to adjust frequency and gain, then release. Bandwidth (or "Q") is only adjustable in the bottom OUTPUT section, using the PEQ BW sliders. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
22
6.C ROUTER (MATRIX)
(middle left screen)
6.C.1 BRIDGE CHANNELS
BRIDGE
1-2
, (
3-4
) button(s) combine amps 1 & 2 (or 3 & 4) for a single high
power output. Use the appropriate output jacks when bridging amps.
*Note: the minimum impedance for a BRIDGED output is
4 ohms
for 2 channel amps, and
8 ohms
for the DCM2004Lx.
6.C.2 OUTPUT MUTES
Click the
MUTE
buttons to mute or un-mute each output.
6.C.3 ROUTING INPUT SOURCES TO OUTPUTS
Click the
A, B,
(
C, D )
buttons select the signal source(s) for each output.
6.C.4 OUTPUT NAME
Click in the
“Output 1”
(etc.) box to type a new name for each output.
6.D FREQUENCY CHART
(middle right screen)
6.D.1 OUTPUT DISPLAY BUTTONS
1, 2 (3, 4)
Displays the frequency response of each amp output as a different color.
6.D.2 ADJUSTING PEQs FROM THE FREQUENCY CHART
The Parametric EQs can be manipulated directly from the Frequency Chart.
Highlight the curve from the lower OUTPUT section with the blue OUTPUT
select 1, 2, (3, 4) buttons. (see
6.E.2
)
Click and drag a round node to adjust frequency and gain, then release.
Bandwidth (or
“Q”) is only adjustable in the bottom OUTPUT section, using
the PEQ BW sliders.