Chamberlain B2212T Installation Manual - English - Page 13

Installation

Get Chamberlain B2212T PDF manuals and user guides View all Chamberlain B2212T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Assembly STEP 5 Tighten the Belt 1. By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley. Do not use any tools. Remove the screwdriver. 2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. 3. Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end wrench about a quarter turn until the spring releases and snaps the nut ring against the trolley. This sets the spring to optimum belt tension. Spring Trolley Nut Nut Ring Slot STEP 6 Install the Sprocket Cover To avoid possible SERIOUS INJURY to finger from moving garage door opener: l ALWAYS keep hand clear of sprocket while operating opener. l Securely attach sprocket cover BEFORE operating. 1. Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with #8x3/8" hex screws provided. You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section. HARDWARE Hex Screw #8x3/8" (Packed with the sprocket cover) Nut Ring Nut Ring Hex Screw Sprocket Cover BEFORE 1" (2.5 cm) AFTER 1-1/4" (3.18 cm) 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
13
Assembly
STEP 5 Tighten the Belt
1.
By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley.
Do not use any tools. Remove the screwdriver.
2.
Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley.
3.
Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end wrench about a quarter
turn until the spring releases and snaps the nut ring against the trolley. This sets the spring to
optimum belt tension.
Spring
Trolley Nut
Nut Ring Slot
Nut Ring
Nut Ring
AFTER
1-1/4" (3.18 cm)
BEFORE
1" (2.5 cm)
STEP 6 Install the Sprocket Cover
To avoid possible SERIOUS INJURY to finger from moving garage door opener:
l
ALWAYS keep hand clear of sprocket while operating opener.
l
Securely attach sprocket cover BEFORE operating.
1.
Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with #8x3/8"
hex screws provided.
You have now finished assembling your garage door opener. Please read the following warnings before
proceeding to the installation section.
Hex Screw #8x3/8"
(Packed with the sprocket cover)
HARDWARE
Hex Screw
Sprocket Cover