Chamberlain B2212T Installation Manual - English - Page 32

Adjustments, Introduction, SAFETY SENSOR TROUBLESHOOTING

Get Chamberlain B2212T PDF manuals and user guides View all Chamberlain B2212T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Installation STEP 16 Align the Safety Reversing Sensors IMPORTANT: The safety reversing sensors MUST be connected and aligned correctly before the garage door opener will move in the down direction. When the garage door opener has power, check the safety reversing sensors. If the sensors are aligned and wired correctly, both LEDs will glow steadily. SAFETY SENSOR TROUBLESHOOTING If either of the sensor LEDs are off, there is no power to the sensor: 1. Check that you have power to the garage door opener. 2. Check the sensor wire is not shorted or broken. 3. Check that the sensors are wired correctly; white wires to white terminal and white/black wires to grey terminal. 1 2 3 Light Beam Protection Area RED WHITE WHITE GREY Sending sensor - amber LED Receiving sensor - green LED The receiving sensor has a To align the safety reversing sensors: sticker on the back. 1. Loosen the wing nuts. 2. Adjust the sensors up or down until both LEDs glow steady indicating alignment. 3. Tighten the wing nut to secure the sensor. If the green receiving sensor LED is blinking, the sensors are obstructed or misaligned: 1. Check for obstructions in the sensor light beam. 2. Align the sensors. 3. If the receiving sensor (green LED) faces direct sunlight, switch the receiving sensor with the sending sensor and repeat STEP 12 Install the Protector System® page 27 to assure proper operation. STEP 17 Ensure the Door Control is Wired Correctly If the door control has been installed and wired correctly, the command LED on the control panel will blink or the LED behind the push button will blink if installed correctly. Wing nut 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
32
Installation
STEP 16 Align the Safety Reversing Sensors
IMPORTANT: The safety reversing sensors MUST be connected and aligned correctly before the garage
door opener will move in the down direction.
When the garage door opener has power, check the safety reversing sensors. If the sensors are aligned and
wired correctly, both LEDs will glow steadily.
Light Beam Protection Area
Receiving sensor - green LED
The receiving sensor has a
sticker on the back.
Sending sensor - amber LED
To align the safety reversing sensors:
1.
Loosen the wing nuts.
2.
Adjust the sensors up or down until both LEDs glow steady indicating alignment.
3.
Tighten the wing nut to secure the sensor.
Wing nut
SAFETY SENSOR TROUBLESHOOTING
If either of the sensor LEDs are off, there is no power to the sensor:
1.
Check that you have power to the garage door opener.
2.
Check the sensor wire is not shorted or broken.
3.
Check that the sensors are wired correctly; white wires to white terminal and white/black wires to grey
terminal.
RED
WHITE
WHITE
GREY
3
2
1
If the green receiving sensor LED is blinking, the sensors are obstructed or misaligned:
1.
Check for obstructions in the sensor light beam.
2.
Align the sensors.
3.
If the receiving sensor (green LED) faces direct sunlight, switch the receiving sensor with the sending
sensor and repeat STEP 12 Install the Protector System® page 27 to assure proper operation.
STEP 17 Ensure the Door Control is Wired Correctly
If the door control has been installed and wired correctly, the command LED on the control panel will blink or
the LED behind the push button will blink if installed correctly.