Chamberlain B2212T Installation Manual - English - Page 25

STEP 11 Wire the Door Control to the Garage Door Opener, STEP 12 Attach the Warning Labels

Get Chamberlain B2212T PDF manuals and user guides View all Chamberlain B2212T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Installation MOTION DETECTING AND MULTI-FUNCTION CONTROL PANEL To prevent possible SERIOUS INJURY or DEATH from electrocution: l Be sure power is NOT connected BEFORE installing door control. l Connect door control ONLY to 12 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: l Install door control within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. l NEVER permit children to operate or play with door control push buttons or remote control transmitters. l Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. l ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door. INTRODUCTION Older Chamberlain door controls and third party products are not compatible. Install door control within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box. NOTE: Your product may look different than the illustrations. Screw 6-32x1" (2) HARDWARE Drywall Anchors (2) Screw 6ABx1" (2) 1. Strip 7/16" (11 mm) of insulation from one end of the wire and separate the wires. 2. Connect one wire to each of the two screws on the back of the door control. The wires can be connected to either screw. If your garage is pre-wired for the door control choose any two wires to connect, note which wires are used so the correct wires are connected to the garage door opener in a later step. 3. Mark the location of the bottom mounting hole and drill a 5/32" hole. 4. Install the bottom screw, allowing 1/8" (3 mm) to protrude from the wall. 5. Position the bottom hole of the door control over the screw and slide down into place. 6. Lift the push bar up and mark the top hole. 7. Remove the door control from the wall and drill a 5/32" hole for the top screw. 8. Position the bottom hole of the door control over the screw and slide down into place. Attach the top screw. 1 2 7/16" (11 mm) 3 Wall 4-5 DRYWALL GANG BOX Drywall Anchor 6ABx1" 6-32x1" 7 8 6 DRYWALL GANG BOX Drywall Anchor 6ABx1" 6-32x1" 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
25
Installation
MOTION DETECTINGAND MULTI-FUNCTION CONTROL PANEL
To prevent possible SERIOUS INJURY or DEATH from electrocution:
l
Be sure power is NOT connected BEFORE installing door control.
l
Connect door control ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
l
Install door control within sight of garage door, out of reach of small children at a minimum height of
5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL
moving parts of door.
l
NEVER permit children to operate or play with door control push buttons or remote control
transmitters.
l
Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to
door travel.
l
ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of
closing garage door.
INTRODUCTION
Older Chamberlain door controls and third party products are not compatible. Install door control within
sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors,
landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. For gang box
installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang
box.
NOTE:
Your product may look different than the illustrations.
Screw
6ABx1" (2)
Drywall
Anchors (2)
Screw
6-32x1" (2)
HARDWARE
1.
Strip 7/16" (11 mm) of insulation from one end of the wire and separate the wires.
2.
Connect one wire to each of the two screws on the back of the door control. The wires can be connected
to either screw. If your garage is pre-wired for the door control choose any two wires to connect, note
which wires are used so the correct wires are connected to the garage door opener in a later step.
3.
Mark the location of the bottom mounting hole and drill a 5/32" hole.
4.
Install the bottom screw, allowing 1/8" (3 mm) to protrude from the wall.
5.
Position the bottom hole of the door control over the screw and slide down into place.
6.
Lift the push bar up and mark the top hole.
7.
Remove the door control from the wall and drill a 5/32" hole for the top screw.
8.
Position the bottom hole of the door control over the screw and slide down into place. Attach the top
screw.
7/16" (11 mm)
Wall
1
2
3
4-5
6
8
7
DRYWALL
GANG BOX
6ABx1"
6-32x1"
Drywall Anchor
DRYWALL
GANG BOX
6ABx1"
6-32x1"
Drywall Anchor