Chamberlain B2212T Installation Manual - English - Page 41

Erase the Memory, To Open the Door Manually

Get Chamberlain B2212T PDF manuals and user guides View all Chamberlain B2212T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Operation Remote Control and Keyless Entry PRE-PROGRAMMED REMOTE CONTROL INCLUDED, NO NEED TO PROGRAM THE REMOTE. To add or reprogram a remote control, follow the instructions below. Older Chamberlain remote controls are NOT compatible. PROGRAM USING THE MOTION DETECTING OR MULTI-FUNCTION CONTROL PANEL 1. Press the LEARN button on the door control to enter programming mode. The command LED will flash once. 2. Press the LEARN button again, the command LED will flash once again. 3. Remote control: Press the button on the remote control that you wish to operate your garage door. Keyless entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. PROGRAM USING THE PUSH BUTTON DOOR CONTROL 1. Press and hold the light button and the push button until the push button LED begins to blink. 2. Remote control: Press the button on the remote control that you wish to operate your garage door. Keyless entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. Push Button LIGHT Button OR PROGRAM USING THE GARAGE DOOR OPENER LEARN BUTTON 1. Locate the LEARN Button. 2. Press and immediately release the LEARN button. The LEARN LED will glow steady for 30 seconds. Within 30 seconds... 3. Remote Control: Press and hold the button on the remote control that you wish to use. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press and hold the ENTER button. Release the button when the garage door opener lights blink or two clicks are heard. 1-2 LEARN Button LEARN LED 3 "clic"kc"lick" OR PIN HomeLink® If your vehicle is equipped with HomeLink®, a Compatibility Bridge™ (not included) may be necessary for certain vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed. OR ???? PIN The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed. Repeat the steps for programming additional remote controls or keyless entry devices. If programming is unsuccessful, repeat the steps using the LEARN button on the garage door opener. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
41
Operation
Remote Control and Keyless Entry
PRE-PROGRAMMED REMOTE CONTROL INCLUDED, NO NEED TO PROGRAM THE
REMOTE.
To add or reprogram a remote control, follow the instructions below. Older Chamberlain remote controls are
NOT compatible.
PROGRAM USING THE MOTION DETECTING OR MULTI-FUNCTION CONTROL PANEL
1.
Press the LEARN button on the door control to enter programming mode. The command LED will flash
once.
2.
Press the LEARN button again, the command LED will flash once again.
3.
Remote control:
Press the button on the remote control that you wish to operate your garage door.
Keyless entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry
keypad. Then press the ENTER button.
PROGRAM USING THE PUSH BUTTON DOOR CONTROL
1.
Press and hold the light button and the push button until the push button LED begins to blink.
2.
Remote control:
Press the button on the remote control that you wish to operate your garage door.
Keyless entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry
keypad. Then press the ENTER button.
PIN
OR
OR
?
?
?
?
Push
Button
LIGHT
Button
The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.
Repeat the steps for programming additional remote controls or keyless entry devices. If programming is
unsuccessful, repeat the steps using the LEARN button on the garage door opener.
PROGRAM USING THE GARAGE DOOR OPENER LEARN BUTTON
1.
Locate the LEARN Button.
2.
Press and immediately release the LEARN button. The LEARN LED will glow steady for 30 seconds.
Within 30 seconds...
3.
Remote Control:
Press and hold the button on the remote control that you wish to use.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry
keypad. Then press and hold the ENTER button.
Release the button when the garage door opener lights blink or two clicks are heard.
“click”
“click”
PIN
OR
1-2
3
LEARN LED
LEARN
Button
HomeLink®
If your vehicle is equipped with HomeLink®, a Compatibility Bridge™ (not included) may be necessary for
certain vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed.