Cisco AIR-BR1310G-A-K9 Hardware Installation Guide - Page 73

Checking Power, Using DHCP Option 43 - r power supply

Get Cisco AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access Point/Bridge PDF manuals and user guides
UPC - 746320927565
View all Cisco AIR-BR1310G-A-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Chapter 5 Troubleshooting Lightweight Access Points Checking Power The power injector is available in two models: • Cisco Aironet Power Injector LR2-standard version (included with the access point) - 48-VDC input power - Uses the 48-VDC power module (included with the access point) • Cisco Aironet Power Injector LR2T-optional transportation version - 12- to 40-VDC input power Checking Power You can verify the availability of power to the lightweight access point by checking the power injector LED (see Figure 5-2): • Power LED - Green color indicates input power is being supplied to the access point. - Red color indicates an overcurrent or overvoltage error condition-disconnect input power from the power injector, check all coax cable connections for a possible short, wait approximately 1 minute, and reconnect input power to the power injector. If the LED turns red again, contact technical support for assistance. Note The power injector requires approximately 50 seconds to recover from an overcurrent or overvoltage condition. - Off indicates input power is not available-verify that the power module is connected to the power injector and that AC power is available or that 12- to 40-VDC input power is connected to the power injector. Using DHCP Option 43 You can use DHCP Option 43 to provide a list of controller IP addresses to the lightweight access points, enabling the access point to find and associate with a controller. For additional information, refer to the "Configuring DHCP Option 43 for Lightweight Access Points" section on page G-1. OL-5048-06 Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide 5-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
5-5
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
OL-5048-06
Chapter 5
Troubleshooting Lightweight Access Points
Checking Power
The power injector is available in two models:
•
Cisco Aironet Power Injector LR2—standard version (included with the access point)
–
48-VDC input power
–
Uses the 48-VDC power module (included with the access point)
•
Cisco Aironet Power Injector LR2T—optional transportation version
–
12- to 40-VDC input power
Checking Power
You can verify the availability of power to the lightweight access point by checking the power injector
LED (see
Figure 5-2
):
•
Power LED
–
Green color indicates input power is being supplied to the access point.
–
Red color indicates an overcurrent or overvoltage error condition—disconnect input power from
the power injector, check all coax cable connections for a possible short, wait approximately
1 minute, and reconnect input power to the power injector. If the LED turns red again, contact
technical support for assistance.
Note
The power injector requires approximately 50 seconds to recover from an overcurrent or
overvoltage condition.
–
Off indicates input power is not available—verify that the power module is connected to the
power injector and that AC power is available or that 12- to 40-VDC input power is connected
to the power injector.
Using DHCP Option 43
You can use DHCP Option 43 to provide a list of controller IP addresses to the lightweight access points,
enabling the access point to find and associate with a controller. For additional information, refer to the
“Configuring DHCP Option 43 for Lightweight Access Points” section on page G-1
.