Cisco C7200-I User Guide - Page 12
show controllers gigabitethernet, Examples - driver
UPC - 746320365398
View all Cisco C7200-I manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
show controllers gigabitethernet Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers Examples The following example displays sample output of the show controllers gigabitethernet command: Router# show controllers gigabitethernet 0/0 Interface GigabitEthernet0/0 (idb 0x627D8344) Hardware is i82543 (Livengood) A1 network connection mode is AUTO network link is up loopback type is none SERDES is enabled (TBI mode), GBIC is enabled GBIC type is 1000BaseSX idb->lc_ip_turbo_fs=0x604A82B0, ip_routecache=0x1(dfs=0/mdfs=0), max_mtu=1524 i82543_ds=0x627DA094, registers=0x3C100000, curr_intr=0 rx cache size=2000, rx cache end=1744, rx_nobuffer=0 i82543 MAC registers: CTRL =0x0ACC0004, STATUS=0x00000FAB, CTRL_X=0x000048E0, IMS =0x00000096 RCTL =0x0042803A, RDBAL =0x2000E000, RDBAH =0x00000000, RDLEN =0x00001000 RDH =0x000000CB, RDT =0x000000CA, RDTR =0x00000000 TCTL =0x000400FA, TDBAL =0x20010000, TDBAH =0x00000000, TDLEN =0x00001000 TDH =0x00000057, TDT =0x00000057, TIPG =0x00600806 ETT =0x00000000, TXDMAC=0x00000001 TXCW =0xC00001A0, RXCW =0xDC004120, FCRTH =0x0000AFF0, FCRTL =0x80001200 FCAH =0x00000100, FCAL =0x00C28001, FCT =0x00008808, FCTTV =0x00000080 RDFH =0x00000BFA, RDFT =0x00000BFA, RDFPC =0x00000000 TDFH =0x00001EBA, TDFT =0x00001EBA, TDFPC =0x00000000 RX is normal, enabled TX is normal, enabled Device status = full-duplex, link up AN status = done(RF:0 , PAUSE:2 ), bit sync OK, rx idle stream, rx invalid symbols, rx idle char GBIC registers: Register 0x00: 01 00 01 00 00 00 01 00 Register 0x08: 00 00 00 00 0D 00 00 00 Register 0x10: 32 1E 00 00 4D 65 74 68 Register 0x18: 6F 64 65 20 45 6C 65 63 Register 0x20: 2E 20 20 20 00 00 00 00 Register 0x28: 4D 47 42 43 2D 32 30 2D Register 0x30: 34 2D 31 2D 53 20 20 20 Register 0x38: 31 30 30 30 00 00 00 55 Register 0x40: 00 0A 00 00 41 4A 42 48 Register 0x48: 47 30 36 30 20 20 20 20 Register 0x50: 20 20 20 20 30 30 30 33 Register 0x58: 32 30 20 20 00 00 00 61 PartNumber:MGBC-20-4-1-S PartRev:G SerialNo:AJBHG060 Options: 0 Length(9um/50um/62.5um):000/500/300 Date Code:000320 Gigabit Ethernet Codes: 1 PCI configuration registers: bus_no=0, device_no=8 DeviceID=0x1001, VendorID=0x8086, Command=0x0156, Status=0x0230 Class=0x02/0x00/0x00, Revision=0x01, LatencyTimer=0xFC, CacheLineSize=0x20 BaseAddr0=0x48100000, BaseAddr1=0x00000000, MaxLat=0x00, MinGnt=0xFF SubsysDeviceID=0x1001, SubsysVendorID=0x8086 Cap_Ptr=0x000000DC Retry/TRDY Timeout=0x00000000 PMC=0x00220001 PMCSR=0x00000000 I82543 Internal Driver Variables: rxring(256)=0x2000E000, shadow=0x627DA3F0, head=203, rx_buf_size=512 txring(256)=0x20010000, shadow=0x627DA81C, head=87, tail=87 chip_state=2, pci_rev=1 tx_count=0, tx_limited=0 rx_overrun=0, rx_seq=0, rx_no_enp=0, rx_discard=0 throttled=0, enabled=0, disabled=0 reset=17(init=1, check=0, restart=3, pci=0), auto_restart=18 12.1(5)T and 12.2(14) S 12