Cisco C7200-I User Guide - Page 5

Verifying the Configuration, show interfaces, ethernet, fastethernet, gigabitethernet - 0 2fe e

Page 5 highlights

Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers Configuration Tasks 3. Use the interface fastethernet router-shelf/slot/port command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access Server. Verifying the Configuration Use the show interfaces {ethernet | fastethernet | gigabitethernet} command to verify that the interface and line protocol are in the correct state (up) and the transmission mode is configured on the interface. You can configure full, half, or auto transmission mode for Ethernet and Fast Ethernet interfaces. You can configure forced transmission mode for Gigabit Ethernet interfaces. The following example displays sample output for a show interfaces gigabitethernet command. Router# show interfaces gigabitethernet 0/0 GigabitEthernet0/0 is up, line protocol is up Hardware is 82543 (Livengood), address is 00d0.ffb6.4c00 (bia 00d0.ffb6.4c00) Internet address is 10.1.1.0/0 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex mode, link type is autonegotiation, media type is SX output flow-control is on, input flow-control is on ARP type:ARPA, ARP Timeout 04:00:00 Last input 00:00:04, output 00:00:03, output hang never Last clearing of "show interface" counters never Queueing strategy:fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 2252 packets input, 135120 bytes, 0 no buffer Received 2252 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 2631 packets output, 268395 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out 12.1(5)T and 12.2(14) S 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers
Configuration Tasks
5
12.1(5)T and 12.2(14) S
Verifying the Configuration
Use the
show interfaces
{
ethernet
|
fastethernet
|
gigabitethernet
} command to verify that the
interface and line protocol are in the correct state (up) and the transmission mode is configured on the
interface. You can configure full, half, or auto transmission mode for Ethernet and Fast Ethernet
interfaces. You can configure forced transmission mode for Gigabit Ethernet interfaces. The following
example displays sample output for a
show interfaces gigabitethernet
command.
Router#
show interfaces gigabitethernet 0/0
GigabitEthernet0/0 is up, line protocol is up
Hardware is 82543 (Livengood), address is 00d0.ffb6.4c00 (bia 00d0.ffb6.4c00)
Internet address is 10.1.1.0/0
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex mode, link type is autonegotiation, media type is SX
output flow-control is on, input flow-control is on
ARP type:ARPA, ARP Timeout 04:00:00
Last input 00:00:04, output 00:00:03, output hang never
Last clearing of "show interface" counters never
Queueing strategy:fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2252 packets input, 135120 bytes, 0 no buffer
Received 2252 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
2631 packets output, 268395 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
3.
Use the
interface fastethernet
router-shelf/slot/port
command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access
Server.