Compaq AP200 Reference Guide - Page 87

Using the SCSI Cable, with a terminator

Get Compaq AP200 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172868534
View all Compaq AP200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

4-23 s Turn on an external SCSI device before turning on power to the workstation. This enables the system board controller to recognize the external SCSI device. When an external SCSI device is connected to the external SCSI connector on the rear panel of the workstation, that device becomes the end of the SCSI chain and must be terminated. CAUTION: Do not route cables near the air intake to the power supply. Cables routed in this manner may block airflow to the power supply causing it to overheat. Using the SCSI Cable The following SCSI cable is included with your workstation (available on select models): 1 Figure 4-16. SCSI cable NOTE: The SCSI cable included with your workstation may look slightly different than the one pictured. The SCSI cable illustrated above supports up to 4 SCSI devices and comes with a terminator 1 on the end. NOTE: If you are installing a narrow SCSI device, you will need to attach a 68- to 50-pin SCSI adapter to the narrow SCSI device. For additional information about installing optional SCSI devices, refer to the documentation included with the device option kit or contact your Compaq authorized dealer, reseller, or service provider. Compaq Professional Workstation AP200 Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
4-23
Compaq Professional Workstation AP200 Reference Guide
■
Turn on an external SCSI device before turning on power to the
workstation. This enables the system board controller to recognize the
external SCSI device. When an external SCSI device is connected to
the external SCSI connector on the rear panel of the workstation, that
device becomes the end of the SCSI chain and must be terminated.
CAUTION:
Do not route cables near the air intake to the power
supply. Cables routed in this manner may block airflow to the
power supply causing it to overheat.
Using the SCSI Cable
The following SCSI cable is included with your workstation (available on
select models):
1
Figure 4-16.
SCSI cable
NOTE
:
The SCSI cable included with your workstation may look slightly
different than the one pictured.
The SCSI cable illustrated above supports up to 4 SCSI devices and comes
with a terminator
1
on the end.
NOTE
:
If you are installing a narrow SCSI device, you will need to attach a
68- to 50-pin SCSI adapter to the narrow SCSI device.
For additional information about installing optional SCSI devices, refer to the
documentation included with the device option kit or contact your Compaq
authorized dealer, reseller, or service provider.