Craftsman 21237 Operation Manual - Page 6

Awarning - miter saw

Get Craftsman 21237 - 10 in. Sliding Miter Saw PDF manuals and user guides View all Craftsman 21237 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

RECOMMENDED ACCESSORIES [AWARNING[ • Use only accessories recommended for this miter saw. Follow instructions that accompany accessories. Use of improper accessories may cause hazards. • The use of any cutting tool except 10 inch saw blades which meet the requirements under recommended accessories is prohibited. Do not use accessories such as shaper cutters or dado sets. Ferrous metal cutting and the use of abrasive wheels is prohibited. = Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. ACCESSORIES Visit your Sears Hardware Department or see the Sears Power and Hand Tool Catalog to purchase recommended accessories for this power tool. [_IL WARNING I To avoid the risk of personal injury, do not modify this power tool or use accessories not recommended by Sears. [_IL WARNING I Read warnings and conditions on your CARBIDE TIPPED SAW BLADE. Do not operate the saw without the proper saw blade guard in place. Carbide is a very hard but brittle material Care should be taken while mounting, using and storing carbide tipped blades to prevent accidental damage. Slight shocks, such as striking the tip while handling, can seriously damage the blade. Foreign objects in the workpiece, such as wire or nails, can also cause tips to crack or break off. Before using, always visually examine the blade and tips for bent blade, cracks, breakage, missing or loose tips, or other damage. Do not use if damage is suspected. Failure to heed safety instructions and warnings can result in serious bodily injury. Supplied Blade Wrench Not supplied Adjustable Wrench Hex Key Combination Square Phillips Screwdriver Slotted Screwdriver COMBINATION SQUARE MUST BE TRUE Should not gap or overlap when square is flipped over (see dotted figure). Straight edge or a 3,/4 in. board, Draw light line on board along this edge. r_ this edge must be perfectly straight. t f I t Gap from untrue square when flipped over. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
RECOMMENDED
ACCESSORIES
[AWARNING[
•
Use only
accessories
recommended
for this
miter saw. Follow instructions
that accompany
accessories.
Use of improper
accessories
may
cause hazards.
•
The use of any cutting tool except
10
inch saw
blades which
meet
the
requirements
under
recommended
accessories
is prohibited.
Do
not use accessories
such
as
shaper cutters or
dado
sets. Ferrous
metal cutting and the use of
abrasive wheels is prohibited.
=
Do
not
attempt
to modify this tool or create
accessories
not recommended
for
use with
this
tool.
Any such
alteration
or modification
is
misuse and could result in a hazardous
condition
leading
to
possible serious
injury.
ACCESSORIES
Visit your Sears Hardware
Department
or see the
Sears Power and Hand Tool Catalog to purchase
recommended
accessories
for this power tool.
[_IL
WARNING
I
To
avoid the
risk of personal injury, do not modify
this
power tool or use accessories not recommended by
Sears.
[_IL WARNING
I
Read warnings and conditions on your CARBIDE TIPPED
SAW BLADE.
Do
not operate the saw without
the
proper
saw
blade
guard in place. Carbide is
a
very hard but
brittle
material
Care should be
taken
while
mounting,
using and storing carbide
tipped
blades to prevent
accidental damage. Slight shocks, such
as
striking
the
tip while handling, can seriously damage the blade.
Foreign
objects
in
the
workpiece, such
as
wire
or
nails,
can
also
cause
tips
to crack
or
break off. Before
using,
always visually examine
the
blade and
tips for bent
blade, cracks, breakage,
missing
or loose tips, or other
damage. Do
not use
if damage is suspected. Failure
to
heed safety instructions
and
warnings can
result
in
serious bodily injury.
Supplied
Blade Wrench
Not supplied
....................
Adjustable Wrench
Hex Key
Combination
Square
Phillips Screwdriver
Slotted
Screwdriver
COMBINATION
SQUARE
MUST
BE
TRUE
Should not gap or overlap when square
is flipped over
(see dotted figure).
Straight edge or
a 3,/4 in. board,
this edge must be
perfectly straight.
Draw light line on board
along
this edge.
r_
t
f
I
t
Gap from untrue square
when flipped over.
6