D-Link DGS-1224T Product Manual - Page 12

Rear Panel, DGS-1224T, Front Panel

Get D-Link DGS-1224T - Web Smart Switch PDF manuals and user guides
UPC - 790069264467
View all D-Link DGS-1224T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3 Product Introduction D-Link Web Smart Switch User Manual NOTE: On DGS-1216T, the MiniGBIC ports 15F and 16F are shared with normal RJ-45 ports 15T and 16T. When MiniGBIC port is used, the RJ-45 port cannot be used. 100/1000M LED (1-14, 15T, 16T): A steady green light denotes a valid 1000Mbps link on the corresponding port, a steady orange light denotes a valid 10 or 100Mbps link on the port. These LEDs will remain dark if there is no link/activity on the port. 1000M LED (15F, 16F): The 1000M LED sign lights up when the corresponding port is running on 1000Mbps. These LEDs will remain dark if there is no link/activity on the port. Rear Panel Figure 9 - DGS-1216T Rear Panel Reset: By pressing the Reset button the Switch will change back to the default configuration and all changes will be lost. Power: The power port is where to connect the AC power cord. DGS-1224T 24 Port 10/100/1000BaseT with 2 Combo SFP Smart Switch Front Panel Figure 10 - DGS-1224T Front Panel Power LED: The Power LED flashes when the Switch is connected to a power source. CPU LED: When the CPU LED is blinking, then the switch is in the normal condition. If the CPU LED is off or stays in solid light state that means the system might have crashed or firmware upgrade has failed. Port Link/Act LED (1-22, 23T/F, 24T/F): The Link/Act LED flashes which indicates a network link through the corresponding port. Blinking state indicates that the Switch is either sending or receiving data to the port. NOTE: On DGS-1224T, the MiniGBIC ports 23F and 24F are shared with normal RJ-45 ports 23T and 24T. When MiniGBIC port is used, the RJ-45 port cannot be used. 100/1000M LED (1-22, 23T, 24T): The 100/1000M LED lights up in steady green denotes a valid 1000Mbps link on the corresponding port, a steady orange light denotes a valid 10 or 100Mbps link on the port. These LEDs will remain dark if there is no link/activity on the port. 1000M LED (23F, 24F): The 1000M LED sign lights up when the corresponding port is running on 1000Mbps. These LEDs will remain dark if there is no link/activity on the port. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
3
Product Introduction
D-Link Web Smart Switch User Manual
NOTE:
On DGS-1216T, the MiniGBIC ports 15F
and 16F are shared with normal RJ-45 ports 15T
and 16T. When MiniGBIC port is used, the RJ-45
port cannot be used.
100/1000M LED (1-14, 15T, 16T):
A steady green light denotes a valid 1000Mbps link on the corresponding
port, a steady orange light denotes a valid 10 or 100Mbps link on the port. These LEDs will remain dark if
there is no link/activity on the port.
1000M LED (15F, 16F):
The 1000M LED sign lights up when the corresponding port is running on 1000Mbps.
These LEDs will remain dark if there is no link/activity on the port.
Rear Panel
Figure 9 – DGS-1216T Rear Panel
Reset:
By pressing the Reset button the Switch will change back to the default configuration and all changes
will be lost.
Power:
The power port is where to connect the AC power cord.
DGS-1224T
24 Port 10/100/1000BaseT with 2 Combo SFP Smart Switch
Front Panel
Figure 10 – DGS-1224T Front Panel
Power LED:
The Power LED flashes when the Switch is connected to a power source.
CPU LED:
When the CPU LED is blinking, then the switch is in the normal condition. If the CPU LED is off or
stays in solid light state that means the system might have crashed or firmware upgrade has failed.
Port Link/Act LED (1-22, 23T/F, 24T/F):
The Link/Act LED flashes which indicates a network link through
the corresponding port. Blinking state indicates that the Switch is either sending or receiving data to the port.
NOTE:
On DGS-1224T, the MiniGBIC ports 23F
and 24F are shared with normal RJ-45 ports 23T
and 24T. When MiniGBIC port is used, the RJ-45
port cannot be used.
100/1000M LED (1-22, 23T, 24T):
The 100/1000M LED lights up in steady green denotes a valid 1000Mbps
link on the corresponding port, a steady orange light denotes a valid 10 or 100Mbps link on the port. These
LEDs will remain dark if there is no link/activity on the port.
1000M LED (23F, 24F):
The 1000M LED sign lights up when the corresponding port is running on 1000Mbps.
These LEDs will remain dark if there is no link/activity on the port.
8