D-Link DGS-3630 User Manual - Page 111

DDM, DDM Settings, Fault messages, Short, CrossTalk, Unknown, OAM > DDM > DDM Settings

Get D-Link DGS-3630 PDF manuals and user guides View all D-Link DGS-3630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

DGS-3630 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Fault messages: • Open - This pair is left open. • Short - Two lines of this pair is shorted. • CrossTalk - Lines of this pair is short with lines in other pairs. • Unknown - The diagnosis does not obtain the cable status, please try again. • NA - No cable was found, maybe it's because cable is out of diagnosis specification or the quality is too bad. DDM This folder contains windows that perform Digital Diagnostic Monitoring (DDM) functions on the Switch. There are windows that allow the user to view the digital diagnostic monitoring status of SFP/SFP+ modules inserting to the Switch and to configure alarm settings, warning settings, temperature threshold settings, voltage threshold settings, bias current threshold settings, Tx power threshold settings, and Rx power threshold settings. DDM Settings The window is used to view and configure the action that will occur for specific ports when an exceeding alarm threshold or warning threshold event is encountered. To view the following window, click OAM > DDM > DDM Settings, as shown below: Figure 8-2 DDM Settings Window The fields that can be configured in DDM Global Settings are described below: Parameter Transceiver Monitoring Traps Alarm Transceiver Monitoring Traps Warning Description Select to enable or disable the transceiver monitoring traps alarm feature here. Select to enable or disable the transceiver monitoring traps warning feature here. Click the Apply button to accept the changes made. 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
DGS-3630 Series Layer 3 Stackable Managed Switch Web UI Reference Guide
104
Fault messages:
•
Open
- This pair is left open.
•
Short
- Two lines of this pair is shorted.
•
CrossTalk
- Lines of this pair is short with lines in other pairs.
•
Unknown
- The diagnosis does not obtain the cable status, please try again.
•
NA
- No cable was found, maybe it's because cable is out of diagnosis specification or the quality is too bad.
DDM
This folder contains windows that perform Digital Diagnostic Monitoring (DDM) functions on the Switch. There are
windows that allow the user to view the digital diagnostic monitoring status of SFP/SFP+ modules inserting to the
Switch and to configure alarm settings, warning settings, temperature threshold settings, voltage threshold settings,
bias current threshold settings, Tx power threshold settings, and Rx power threshold settings.
DDM Settings
The window is used to view and configure the action that will occur for specific ports when an exceeding alarm
threshold or warning threshold event is encountered.
To view the following window, click
OAM > DDM > DDM Settings
, as shown below:
Figure 8-2 DDM Settings Window
The fields that can be configured in
DDM Global Settings
are described below:
Parameter
Description
Transceiver Monitoring
Traps Alarm
Select to enable or disable the transceiver monitoring traps alarm feature here.
Transceiver Monitoring
Traps Warning
Select to enable or disable the transceiver monitoring traps warning feature
here.
Click the
Apply
button to accept the changes made.