D-Link DWC-1000-WCF-LIC User Guide - Page 33

Basic Configuration Step #1. Enable DHCP Server Optional

Get D-Link DWC-1000-WCF-LIC PDF manuals and user guides View all D-Link DWC-1000-WCF-LIC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Basic Configuration Basic Configuration Step #1. Enable DHCP Server (Optional) By default, Dynamic Host Configuration Protocol (DHCP) is disabled in the wireless controller. If you are not configuring your access points with static IP addresses, set up a DHCP server or DHCP server relay on the network. If desired, perform the following procedure to configure your wireless controller to act as a DHCP server. 1. Click SETUP > Network Settings > LAN Setup Configuration. The LAN SETUP page appears. 2. Under LAN IP Address Setup, change the IP Address and Subnet Mask to values used within your network. Record the settings below; you will refer to them later in this procedure: - IP address Subnet mask 3. Click Save Settings. 4. Wait 60 seconds, and then start your web browser. 33 DWC-1000 Wireless Controller User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
Basic Configuration
33
DWC-1000 Wireless Controller
User’s
Guide
Basic Configuration Step #1. Enable DHCP Server (Optional)
By default, Dynamic Host Configuration Protocol (DHCP) is disabled in the wireless
controller. If you are not configuring your access points with static IP addresses, set up a
DHCP server or DHCP server relay on the network. If desired, perform the following
procedure to configure your wireless controller to act as a DHCP server.
1. Click
SETUP > Network Settings > LAN Setup Configuration
. The LAN SETUP page
appears.
2. Under
LAN IP Address Setup
, change the
IP Address
and
Subnet Mask
to values used
within your network. Record the settings below; you will refer to them later in this
procedure:
–
IP address: ___________________________________________
–
Subnet mask: _________________________________________
3. Click
Save Settings
.
4. Wait 60 seconds, and then start your web browser.