DIRECTV H20 User Guide - Page 82

If you get a bunch of new equipment lucky you, you may find it useful to reset your remote before, - customer service

Get DIRECTV H20 PDF manuals and user guides View all DIRECTV H20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

If you get a bunch of new equipment (lucky you!), you may find it useful to reset your remote before you re-program it. 5) Highlight the System Test tab and press SELECT, then press SELECT on Run Test. 6) If your system does not pass the system test, check any of these potential trouble areas: cabling, pointing the satellite dish, phone connection and access card. 7) If you continue to have problems, call DIRECTV Customer Service at 1-800-DIRECTV. You should run a system test several times before concluding that there is a problem. Occasional fluctuations in the phone line or satellite signal can give temporary false readings. Factory Defaults To reset all the remote control and clear all but DIRECTV mode, follow these steps: 1) Point the remote away from your DIRECTV Receiver and components. Press and hold MUTE and SELECT until the light above the slide switch on the remote flashes twice (about 5 seconds). 2) Enter 9-8-1. The light on the remote will flash twice, indicating you have cleared AV1, AV2 and TV modes. Resolutions and Formats The tables on the next page show the formats and resolutions supported by the DIRECTV HD Receiver, the interaction with the FORMAT key, the outputs supported by the different types of connections, and other, related information. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
74
5)
Highlight the
System Test
tab and press SELECT, then press SELECT on
Run Test
.
6)
If your system does not pass the system test, check any of these potential trouble areas: cabling, pointing the
satellite dish, phone connection and
access card.
7)
If you continue to have problems, call DIRECTV Customer Service at 1-800-DIRECTV.
You should run a system test several times before concluding that there is a problem. Occasional fluctuations in the
phone line or satellite signal can give temporary false readings.
Factory Defaults
To reset all the
remote control and clear all but DIRECTV mode, follow these steps:
1)
Point the
remote away from your DIRECTV Receiver and components. Press and hold
MUTE and SELECT
until the light above the slide switch on the
remote flashes twice (about 5 seconds).
2)
Enter 9-8-1. °e light on the
remote will flash twice, indicating you have cleared AV1, AV2 and TV modes.
Resolutions and Formats
°e tables on the next page show the formats and resolutions supported by the DIRECTV HD Receiver, the
interaction with the FORMAT key, the outputs supported by the different types of connections, and other, related
information.
If you get a bunch of new equipment (lucky you!),
you may find it useful to reset your remote before
you re-program it.