Dell Dimension 3100C Owner's Manual - Page 98

Clearing Password Settings, After the Microsoft

Get Dell Dimension 3100C PDF manuals and user guides View all Dell Dimension 3100C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

www.dell.com | support.dell.com Clearing Password Settings 1 Follow the procedures in "Before You Begin" on page 53. 2 Locate the 3-pin password jumper (PSWD) on the system board (see page 97), and attach the jumper plug to pins 2 and 3 to clear the password. NOTE: When you receive your computer, the jumper plug is attached to pins 1 and 2. 3 Close the computer cover (see page 84). 4 Connect your computer and monitor to electrical outlets, and turn them on. 5 After the Microsoft® Windows® desktop appears on your computer, shut down the computer (see page 53). 6 Turn off the monitor and disconnect it from the electrical outlet. 7 Disconnect the computer power cable from the electrical outlet, and press the power button to ground the system board. 8 Open the computer cover (see page 58). 9 Locate the 3-pin password jumper (PSWD) on the system board (see page 61) and attach the jumper to pins 1 and 2 to reenable the password feature. 10 Replace the computer cover (see page 84). NOTICE: To connect a network cable, first plug the cable into the network port or device, and then plug it into the computer. 11 Connect your computer and devices to electrical outlets, and turn them on. Clearing CMOS Settings CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. 1 Follow the procedures in "Before You Begin" on page 53. 2 Reset the current CMOS settings: a Locate the 3-pin CMOS jumper (RTCRST) on the system board (see page 97). b Remove the jumper plug from pins 2 and 3. c Place the jumper plug on pins 1 and 2 and wait approximately five seconds. d Replace the jumper plug on pins 2 and 3. 3 Replace the computer cover (see page 84). NOTICE: To connect a network cable, first plug the cable into the network port or device, and then plug it into the computer. 4 Connect your computer and devices to electrical outlets, and turn them on. 98 Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
98
Appendix
www.dell.com | support.dell.com
Clearing Password Settings
1
Follow the procedures in "Before You Begin" on page53.
2
Locate the 3-pin password jumper (PSWD) on the system board (see page 97), and attach the
jumper plug to pins 2 and 3 to clear the password.
NOTE:
When you receive your computer, the jumper plug is attached to pins 1 and 2.
3
Close the computer cover (see page 84).
4
Connect your computer and monitor to electrical outlets, and turn them on.
5
After the Microsoft
®
Windows
®
desktop appears on your computer, shut down the computer
(see page 53).
6
Turn off the monitor and disconnect it from the electrical outlet.
7
Disconnect the computer power cable from the electrical outlet, and press the power button
to ground the system board.
8
Open the computer cover (see page 58).
9
Locate the 3-pin password jumper (PSWD) on the system board (see page 61) and attach the
jumper to pins 1 and 2 to reenable the password feature.
10
Replace the computer cover (see page 84).
NOTICE:
To connect a network cable, first plug the cable into the network port or device, and then plug
it into the computer.
11
Connect your computer and devices to electrical outlets, and turn them on.
Clearing CMOS Settings
CAUTION:
Before you begin any of the procedures in this section, follow the safety instructions
located in the
Product Information Guide
.
1
Follow the procedures in "Before You Begin" on page53.
2
Reset the current CMOS settings:
a
Locate the 3-pin CMOS jumper (RTCRST) on the system board (see page 97).
b
Remove the jumper plug from pins 2 and 3.
c
Place the jumper plug on pins 1 and 2 and wait approximately five seconds.
d
Replace the jumper plug on pins 2 and 3.
3
Replace the computer cover (see page 84).
NOTICE:
To connect a network cable, first plug the cable into the network port or device, and then plug
it into the computer.
4
Connect your computer and devices to electrical outlets, and turn them on.