Dell EqualLogic PS6210S PS6210 Hardware Owners Manual - Page 8

Array Bezel, Removing the Bezel, Installing the Bezel

Get Dell EqualLogic PS6210S PDF manuals and user guides View all Dell EqualLogic PS6210S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

PS6210 Hardware Owner's Manual 1 Basic Storage Array Information Figure 1: Using an Electrostatic Wrist Strap 2. Fit the band tightly around your wrist. 3. Connect the band to ground. You can either plug the banana connector into a matching grounded receptacle, or attach it to the matching alligator clip and connect the clip to a grounded device. Examples of an appropriate ground would be an ESD mat or the metal frame of a grounded piece of equipment. Array Bezel The bezel is an optional trim panel that attaches to the front of the array to ensure the physical security of the array. You must remove the bezel to access and maintain the drives. The bezel has a label that identifies the array model number. Removing the Bezel The steps for removing the bezel are the same for all array models: 1. Using the bezel key, unlock the bezel. 2. Holding the bezel, lift the latch on the left side of the bezel and swing the left side away from the array. 3. Lift the right side of the bezel off the right side of the array. 4. Set the bezel aside. Installing the Bezel The steps for installing the bezel are the same for all array models: 1. Hook the right end of the bezel onto the right side of the chassis. 2. Swing the left end of the bezel toward the left side of the chassis. 3. Press the bezel into place until the release latch closes. 4. Using the key provided, lock the bezel and store the key in a safe place as shown in Figure 2 and Figure 3. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Figure 1: Using an Electrostatic Wrist Strap
2.
Fit the band tightly around your wrist.
3.
Connect the band to ground. You can either plug the banana connector into a matching grounded
receptacle, or attach it to the matching alligator clip and connect the clip to a grounded device.
Examples of an appropriate ground would be an ESD mat or the metal frame of a grounded piece
of equipment.
Array Bezel
The bezel is an optional trim panel that attaches to the front of the array to ensure the physical
security of the array. You must remove the bezel to access and maintain the drives.
The bezel has a label that identifies the array model number.
Removing the Bezel
The steps for removing the bezel are the same for all array models:
1.
Using the bezel key, unlock the bezel.
2.
Holding the bezel, lift the latch on the left side of the bezel and swing the left side away from the
array.
3.
Lift the right side of the bezel off the right side of the array.
4.
Set the bezel aside.
Installing the Bezel
The steps for installing the bezel are the same for all
array models:
1.
Hook the right end of the bezel onto the right side of the chassis.
2.
Swing the left end of the bezel toward the left side of the chassis.
3.
Press the bezel into place until the release latch closes.
4.
Using the key provided, lock the bezel and store the key in a safe place as shown in
Figure 2
and
Figure 3
.
2
PS6210 Hardware Owner's Manual
1 Basic Storage Array Information