Dell Inspiron 13 5310 Service Manual - Page 17

Removing the M.2 2280 solid-state drive, Next steps, Prerequisites, About this task

Get Dell Inspiron 13 5310 PDF manuals and user guides View all Dell Inspiron 13 5310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3. Place and slide the M.2 2230 bracket on the system board, aligning the notch on the M.2 2230 bracket to the groove on the M.2 2230 solid-state drive. 4. Replace the screw (M2x3) that secures the M.2 2230 bracket to the system board. 5. Place the Mylar over the system board. Next steps 1. Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. Removing the M.2 2280 solid-state drive Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task NOTE: This procedure applies only to computers shipped with a M.2 2280 solid-state drive installed. NOTE: The M.2 card installed on your computer will depend on the configuration ordered. The supported card configurations on the M.2 card slota are: ● M.2 2230 solid-state drive + 2230 mounting bracket ● M.2 2280 solid-state drive The following image(s) indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the removal procedure. Removing and installing components 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
3.
Place and slide the M.2 2230 bracket on the system board, aligning the notch on the M.2 2230 bracket to the groove on the
M.2 2230 solid-state drive.
4.
Replace the screw (M2x3) that secures the M.2 2230 bracket to the system board.
5.
Place the Mylar over the system board.
Next steps
1.
Install the
base cover
.
2.
Exit
Service Mode
.
3.
Follow the procedure in
After working inside your computer
.
Removing the M.2 2280 solid-state drive
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Enter
Service Mode
.
3.
Remove the
base cover
.
About this task
NOTE:
This procedure applies only to computers shipped with a M.2 2280 solid-state drive installed.
NOTE:
The M.2 card installed on your computer will depend on the configuration ordered. The supported card
configurations on the M.2 card slota are:
●
M.2 2230 solid-state drive + 2230 mounting bracket
●
M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the
removal procedure.
Removing and installing components
17