Dell Inspiron 13 5310 Service Manual - Page 34

Display assembly, Removing the display assembly

Get Dell Inspiron 13 5310 PDF manuals and user guides View all Dell Inspiron 13 5310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Steps 1. Place the touchpad on the palm-rest and keyboard assembly. 2. Turn the computer over and open the display to ensure that the touchpad is equally aligned on all sides. 3. Close the display and place the computer in the position shown. 4. Replace the two screws (M2x2) that secure the touchpad to the palm-rest and keyboard assembly. 5. Place the touchpad bracket on the touchpad. 6. Align the screw holes on the touchpad bracket to the screw holes on the palm-rest and keyboard assembly. 7. Replace the four screws (M2x2) that secure the touchpad bracket to the palm-rest and keyboard assembly. 8. Connect the touchpad cable to the system board and close the latch. Next steps 1. Install the battery. 2. Install the base cover. 3. Follow the procedure in After working inside your computer. Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task The following image(s) indicate the location of the display assembly and provides a visual representation of the removal procedure. 34 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Steps
1.
Place the touchpad on the palm-rest and keyboard assembly.
2.
Turn the computer over and open the display to ensure that the touchpad is equally aligned on all sides.
3.
Close the display and place the computer in the position shown.
4.
Replace the two screws (M2x2) that secure the touchpad to the palm-rest and keyboard assembly.
5.
Place the touchpad bracket on the touchpad.
6.
Align the screw holes on the touchpad bracket to the screw holes on the palm-rest and keyboard assembly.
7.
Replace the four screws (M2x2) that secure the touchpad bracket to the palm-rest and keyboard assembly.
8.
Connect the touchpad cable to the system board and close the latch.
Next steps
1.
Install the
battery
.
2.
Install the
base cover
.
3.
Follow the procedure in
After working inside your computer
.
Display assembly
Removing the display assembly
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Enter
Service Mode
.
3.
Remove the
base cover
.
About this task
The following image(s) indicate the location of the display assembly and provides a visual representation of the removal
procedure.
34
Removing and installing components