Dell Inspiron 13 5310 Service Manual - Page 40

I/O board, Removing the I/O board

Get Dell Inspiron 13 5310 PDF manuals and user guides View all Dell Inspiron 13 5310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

14. Replace the screw (M2x3) that secures the display-cable bracket to the system board. 15. Adhere the tape that secures the display-cable bracket to the system board. Next steps 1. Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. I/O board Removing the I/O board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure. Steps 1. Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the I/O board. 2. Remove the screw (M2x3) that secures the left-display hinge to the palm-rest and keyboard assembly. 3. Remove the screw (M2x4) that secures the left-display hinge to the palm-rest and keyboard assembly. 4. Pry open the left-display hinge. 5. Remove the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly. 40 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
14.
Replace the screw (M2x3) that secures the display-cable bracket to the system board.
15.
Adhere the tape that secures the display-cable bracket to the system board.
Next steps
1.
Install the
base cover
.
2.
Exit
Service Mode
.
3.
Follow the procedure in
After working inside your computer
.
I/O board
Removing the I/O board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Enter
Service Mode
.
3.
Remove the
base cover
.
About this task
The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure.
Steps
1.
Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the I/O board.
2.
Remove the screw (M2x3) that secures the left-display hinge to the palm-rest and keyboard assembly.
3.
Remove the screw (M2x4) that secures the left-display hinge to the palm-rest and keyboard assembly.
4.
Pry open the left-display hinge.
5.
Remove the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.
40
Removing and installing components