Dell Inspiron 14 5485 2-in-1 Inspiron 5485 2-in-1 Service Manual - Page 48

Removing the display assembly, Prerequisites, Procedure

Get Dell Inspiron 14 5485 2-in-1 PDF manuals and user guides View all Dell Inspiron 14 5485 2-in-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

30 Removing the display assembly WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the base cover. 2 Remove the wireless card. Procedure 1 Peel off the tape that secures the fan cable to the palm-rest and keyboard assembly. 2 Disconnect the fan cable from the system board. 3 Open the latch, and disconnect the I/O cable from the system board. 4 Peel off the tape that secures the touchscreen cable and the display cable to their respective connectors on the system board. 5 Open the latch, and disconnect the touchscreen cable from the system board. 6 Open the latch, and disconnect the display cable from the system board. 7 Turn the computer over, and open the display as far as possible. Then place the computer face down on a flat surface. CAUTION: Place the computer on a soft and clean surface to avoid scratching the display. 8 Remove the antenna cables from the routing guides on the palm-rest and keyboard assembly. 9 Remove the six screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly. 10 Gently lift the display assembly off the palm-rest and keyboard assembly. 48 Removing the display assembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Removing the display assembly
WARNING:
Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working inside
your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Prerequisites
1
Remove the
base cover
.
2
Remove the
wireless card
.
Procedure
1
Peel
off
the tape that secures the fan cable to the palm-rest and keyboard assembly.
2
Disconnect the fan cable from the system board.
3
Open the latch, and disconnect the I/O cable from the system board.
4
Peel
off
the tape that secures the touchscreen cable and the display cable to their respective connectors on the system board.
5
Open the latch, and disconnect the touchscreen cable from the system board.
6
Open the latch, and disconnect the display cable from the system board.
7
Turn the computer over, and open the display as far as possible. Then place the computer face down on a
flat
surface.
CAUTION:
Place the computer on a soft and clean surface to avoid scratching the display.
8
Remove the antenna cables from the routing guides on the palm-rest and keyboard assembly.
9
Remove the six screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly.
10
Gently lift the display assembly
off
the palm-rest and keyboard assembly.
30
48
Removing the display assembly