Dell Inspiron 14 5485 2-in-1 Inspiron 5485 2-in-1 Service Manual - Page 50

Replacing the display assembly, Procedure

Get Dell Inspiron 14 5485 2-in-1 PDF manuals and user guides View all Dell Inspiron 14 5485 2-in-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

31 Replacing the display assembly WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 CAUTION: Place the computer on a soft and clean surface to avoid scratching the display. Align the screw holes on the display assembly with the screw holes on the palm-rest and keyboard assembly. 2 Replace the six screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly. 3 Route the antenna cables through the routing guides on the palm-rest and keyboard assembly. 4 Close the display, and turn the computer over. 5 Connect the fan cable to the system board. 6 Adhere the tape that secures the fan cable to the palm-rest and keyboard assembly. 7 Slide the I/O cable into the slot on the system board and close the latches to secure the cable. 8 Slide the touchscreen cable into the slot on the system board and close the latch to secure the cable. 9 Slide the display cable into the slot on the system board and close the latch to secure the cable. 10 Adhere the tape that secures the touchscreen cable to the system board. 11 Adhere the tape that secures the display cable to the system board. 50 Replacing the display assembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Replacing the display assembly
WARNING:
Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working inside
your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Procedure
1
CAUTION:
Place the computer on a soft and clean surface to avoid scratching the display.
Align the screw holes on the display assembly with the screw holes on the palm-rest and keyboard assembly.
2
Replace the six screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly.
3
Route the antenna cables through the routing guides on the palm-rest and keyboard assembly.
4
Close the display, and turn the computer over.
5
Connect the fan cable to the system board.
6
Adhere the tape that secures the fan cable to the palm-rest and keyboard assembly.
7
Slide the I/O cable into the slot on the system board and close the latches to secure the cable.
8
Slide the touchscreen cable into the slot on the system board and close the latch to secure the cable.
9
Slide the display cable into the slot on the system board and close the latch to secure the cable.
10
Adhere the tape that secures the touchscreen cable to the system board.
11
Adhere the tape that secures the display cable to the system board.
31
50
Replacing the display assembly