Dell Inspiron 3020 Small Desktop Service Manual - Page 19

Optical drive (optional), Removing the optical drive

Get Dell Inspiron 3020 Small Desktop PDF manuals and user guides View all Dell Inspiron 3020 Small Desktop manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Steps 1. Connect the data and power cables to the connectors on the optical drive. 2. Route the data and power cables through the routing guides on the hard-drive and optical-drive bracket. 3. Hold the hard-drive and optical-drive bracket near the chassis, and connect the data and power cables to the connectors on the optical drive. NOTE: Skip this step if the computer is not shipped with an optical drive. 4. Turn over and align the hard-drive and optical-drive bracket to the chassis. 5. Slide and insert the bracket at an angle and place it down on the chassis. 6. Replace the (#6-32) screw to secure the hard-drive and optical-drive bracket to the chassis. Next steps 1. Install the 3.5-inch hard drive or 2.5-inch hard drive. 2. Install the front cover. 3. Install the left-side cover. 4. Follow the procedure in After working inside your computer. Optical drive (optional) Removing the optical drive Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 3. Remove the front cover. 4. Remove the 3.5-inch hard drive or 2.5-inch hard drive. 5. Remove the hard-drive and optical-drive cage. About this task NOTE: Depending on the configuration ordered, your computer may not have an optical drive installed. The following image indicates the location of the optical drive and provides a visual representation of the removal procedure. Removing and installing components 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Steps
1.
Connect the data and power cables to the connectors on the optical drive.
2.
Route the data and power cables through the routing guides on the hard-drive and optical-drive bracket.
3.
Hold the hard-drive and optical-drive bracket near the chassis, and connect the data and power cables to the connectors on
the optical drive.
NOTE:
Skip this step if the computer is not shipped with an optical drive.
4.
Turn over and align the hard-drive and optical-drive bracket to the chassis.
5.
Slide and insert the bracket at an angle and place it down on the chassis.
6.
Replace the (#6-32) screw to secure the hard-drive and optical-drive bracket to the chassis.
Next steps
1.
Install the
3.5-inch hard drive
or
2.5-inch hard drive
.
2.
Install the
front cover
.
3.
Install the
left-side cover
.
4.
Follow the procedure in
After working inside your computer
.
Optical drive (optional)
Removing the optical drive
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
left-side cover
.
3.
Remove the
front cover
.
4.
Remove the
3.5-inch hard drive
or
2.5-inch hard drive
.
5.
Remove the
hard-drive and optical-drive cage
.
About this task
NOTE:
Depending on the configuration ordered, your computer may not have an optical drive installed.
The following image indicates the location of the optical drive and provides a visual representation of the removal procedure.
Removing and installing components
19