Dell Inspiron 7405 2-in-1 Inspiron 7405 2n1 Service Manual - Page 40

Display assembly, Removing the display assembly

Get Dell Inspiron 7405 2-in-1 PDF manuals and user guides View all Dell Inspiron 7405 2-in-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Steps 1. Align and place the power button, along with its cable, on the slot of the palm-rest and keyboard assembly. 2. Slide the power-button cable into the connector on the fingerprint reader-board and close the latch to secure the cable. 3. Connect the fingerprint reader-cable to the connector on the I/O board and close the latch to secure the cable. 4. Connect the I/O-board cable to the connector on the I/O board and close the latch to secure the cable. 5. Adhere the tape that secures the I/O-board cable to the I/O board. 6. Align the screw holes on the power-button bracket with the screw holes on the palm-rest and keyboard assembly. 7. Replace the two screws (M2x3) that secure power-button bracket to the palm-rest and keyboard assembly. Next steps 1. Install the fan. 2. Install the heat sink. 3. Install the base cover. 4. Follow the procedure in After working inside your computer. Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task The following image indicates the location of the display assembly and provides a visual representation of the removal procedure. 40 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Steps
1.
Align and place the power button, along with its cable, on the slot of the palm-rest and keyboard assembly.
2.
Slide the power-button cable into the connector on the fingerprint reader-board and close the latch to secure the cable.
3.
Connect the fingerprint reader-cable to the connector on the I/O board and close the latch to secure the cable.
4.
Connect the I/O-board cable to the connector on the I/O board and close the latch to secure the cable.
5.
Adhere the tape that secures the I/O-board cable to the I/O board.
6.
Align the screw holes on the power-button bracket with the screw holes on the palm-rest and keyboard assembly.
7.
Replace the two screws (M2x3) that secure power-button bracket to the palm-rest and keyboard assembly.
Next steps
1.
Install the
fan
.
2.
Install the
heat sink
.
3.
Install the
base cover
.
4.
Follow the procedure in
After working inside your computer
.
Display assembly
Removing the display assembly
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
The following image indicates the location of the display assembly and provides a visual representation of the removal procedure.
40
Removing and installing components