Dell N3200-ON Open Networking Hardware Diagnostic Guide July 2022 - Page 18

Dell DIAG OS for N2200-ON and N3200-ON/E3200-ON Series, DIAG OS installation or update

Get Dell N3200-ON PDF manuals and user guides View all Dell N3200-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

5 Dell DIAG OS for N2200-ON and N3200-ON/ E3200-ON Series These sections describe Dell diagnostics. Topics: • DIAG OS installation or update • Diagnostic test suite • View DIAG versions • View CPLD versions DIAG OS installation or update Load or update the DIAG-OS-the diag installer image-using the onie-nos-install command. The DIAG-OS installer runs in two modes: Update mode or Install mode. ● In Update mode, the DIAG-OS updates the existing DIAG-OS and boots back to ONIE. ● In Install mode, the DIAG-OS erases the existing DIAG-OS and loads the new DIAG-OS. NOTE: If you have a recovery USB plugged into your system, remove it before using the onie-nos-install command. NOTE: Before you begin, go to www.dell.com/support and download the diagnostic package. 1. Enter the onie-discovery-stop command to stop ONIE Discovery mode. 2. Assign an IP address to the management interface and verify the network connectivity. ONIE:/ # ifconfig eth0 xx.xx.xx.xx netmask xxx.xxx.x.x up ONIE:/ # ifconfig eth0 Link encap:Ethernet HWaddr 34:17:EB:05:B4:00 inet addr:xx.xx.xx.xx Bcast:xx.xx.xxx.xxx Mask:xxx.xxx.x.x inet6 addr: fe80::3617:ebff:fe05:b400/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:31 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5118 (4.9 KiB) TX bytes:7104 (6.9 KiB) Memory:dff40000-dff5ffff 3. Upgrade the DIAG Installer. NOTE: In Install mode, the DIAG-OS installation removes any existing NOS and DIAG-OS partition. If you do not create file /tmp/diag_os_install_mode, the DIAG-OS installs in Upgrade mode. In this case, the installation process does NOT touch any existing NOS. 4. Start diagnostics. To start the diagnostics, use the EDA-DIAG option from the GRUB menu. a. Boot into the EDA DIAGs. b. Log in as root. Password: calvin. c. Install the EDA-DIAG tools package. NOTE: To return to your networking operating software, enter the reboot command. 18 Dell DIAG OS for N2200-ON and N3200-ON/E3200-ON Series

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Dell DIAG OS for N2200-ON and N3200-ON/
E3200-ON Series
These sections describe Dell diagnostics.
Topics:
•
DIAG OS installation or update
•
Diagnostic test suite
•
View DIAG versions
•
View CPLD versions
DIAG OS installation or update
Load or update the DIAG-OS—the diag installer image—using the
onie-nos-install
command. The DIAG-OS installer runs
in two modes: Update mode or Install mode.
●
In Update mode, the DIAG-OS updates the existing DIAG-OS and boots back to ONIE.
●
In Install mode, the DIAG-OS erases the existing DIAG-OS and loads the new DIAG-OS.
NOTE:
If you have a recovery USB plugged into your system, remove it before using the
onie-nos-install
command.
NOTE:
Before you begin, go to
www.dell.com/support
and download the diagnostic package.
1.
Enter the
onie-discovery-stop
command to stop ONIE Discovery mode.
2.
Assign an IP address to the management interface and verify the network connectivity.
ONIE:/ # ifconfig eth0 xx.xx.xx.xx netmask xxx.xxx.x.x up
ONIE:/ # ifconfig
eth0
Link encap:Ethernet
HWaddr 34:17:EB:05:B4:00
inet addr:xx.xx.xx.xx
Bcast:xx.xx.xxx.xxx
Mask:xxx.xxx.x.x
inet6 addr: fe80::3617:ebff:fe05:b400/64 Scope:Link
UP BROADCAST RUNNING MULTICAST
MTU:1500
Metric:1
RX packets:43 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5118 (4.9 KiB)
TX bytes:7104 (6.9 KiB)
Memory:dff40000-dff5ffff
3.
Upgrade the DIAG Installer.
NOTE:
In Install mode, the DIAG-OS installation removes any existing NOS and DIAG-OS partition. If you do not create
file /tmp/diag_os_install_mode
, the DIAG-OS installs in Upgrade mode. In this case, the installation process
does NOT touch any existing NOS.
4.
Start diagnostics.
To start the diagnostics, use the
EDA-DIAG
option from the GRUB menu.
a.
Boot into the EDA DIAGs.
b.
Log in as
root
.
Password:
calvin
.
c.
Install the EDA-DIAG tools package.
NOTE:
To return to your networking operating software, enter the
reboot
command.
5
18
Dell DIAG OS for N2200-ON and N3200-ON/E3200-ON Series