Dell PowerEdge 1900 Hardware Owner's Manual (PDF) - Page 29

Check the Time and Date settings. See, Update the BIOS firmware. See Getting - processor upgrade

Get Dell PowerEdge 1900 PDF manuals and user guides View all Dell PowerEdge 1900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Table 1-5. System Messages (continued) Message Causes Corrective Actions The amount of system memory has changed Memory has been added or removed or a memory module may be faulty. If memory has been added or removed, this message is informative and can be ignored. If memory has not been added or removed, check the SEL to determine if single-bit or multi-bit errors were detected and replace the faulty memory module. See "Troubleshooting System Memory" on page 110. The following DIMM pair is not compatible with the memory controller: DIMM x and DIMM y The specified DIMM(s) are incompatible with the system. Ensure that only Dell-qualified memory is used. Dell recommends purchasing memory upgrade kits directly from www.dell.com or your Dell sales agent to ensure compatibility. The following DIMMs are The specified DIMM(s) are not compatible: DIMM x and incompatible with the system. DIMM y Ensure that only ECC FBD1 memory is used. Dell recommends purchasing memory upgrade kits directly from www.dell.com or your Dell sales agent to ensure compatibility. Time-of-day clock stopped Faulty battery or faulty chip. See "Troubleshooting the System Battery" on page 108. Time-of-day not set please run SETUP program Incorrect Time or Date settings; faulty Check the Time and Date settings. See system battery. "Using the System Setup Program" on page 33. If the problem persists, replace the system battery. See "System Battery" on page 75. Timer chip counter 2 failed Faulty system board. See "Getting Help" on page 131. Unsupported CPU combination Unsupported CPU stepping detected Microprocessor(s) is not supported by Install a supported microprocessor or the system. microprocessor combination. See "Microprocessor" on page 87. Utility partition not available The key was pressed during POST, but no utility partition exists on the boot hard drive. Create a utility partition on the boot hard drive. See the CDs that came with your system. Warning! No microcode update loaded for processor n Microcode update failed. Update the BIOS firmware. See "Getting Help" on page 131. About Your System 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
About Your System
29
The amount of system
memory has changed
Memory has been added or removed
or a memory module may be faulty.
If memory has been added or removed,
this message is informative and can be
ignored. If memory has not been added
or removed, check the SEL to determine
if single-bit or multi-bit errors were
detected and replace the faulty memory
module. See "Troubleshooting System
Memory" on page 110.
The following DIMM pair is
not compatible with the
memory controller: DIMM x
and DIMM y
The specified DIMM(s) are
incompatible with the system.
Ensure that only Dell-qualified memory
is used. Dell recommends purchasing
memory upgrade kits directly from
www.dell.com
or your Dell sales agent to
ensure compatibility.
The following DIMMs are
not compatible: DIMM x and
DIMM y
The specified DIMM(s) are
incompatible with the system.
Ensure that only ECC FBD1 memory is
used. Dell recommends purchasing
memory upgrade kits directly from
www.dell.com
or your Dell sales agent to
ensure compatibility.
Time-of-day clock stopped
Faulty battery or faulty chip.
See "Troubleshooting the System
Battery" on page 108.
Time-of-day not set -
please run SETUP program
Incorrect Time or Date settings; faulty
system battery.
Check the Time and Date settings. See
"Using the System Setup Program" on
page 33. If the problem persists, replace
the system battery. See "System Battery"
on page 75.
Timer chip counter 2
failed
Faulty system board.
See "Getting Help" on page 131.
Unsupported CPU
combination
Unsupported CPU stepping
detected
Microprocessor(s) is not supported by
the system.
Install a supported microprocessor or
microprocessor combination. See
"Microprocessor" on page 87.
Utility partition not
available
The <F10> key was pressed during
POST, but no utility partition exists
on the boot hard drive.
Create a utility partition on the boot
hard drive. See the CDs that came with
your system.
Warning! No microcode
update loaded for
processor
n
Microcode update failed.
Update the BIOS firmware. See "Getting
Help" on page 131.
Table 1-5.
System Messages
(continued)
Message
Causes
Corrective Actions