Dell PowerEdge 1950 Information Update - Page 11

Table 1-1., System Messages, Message, Causes, Corrective Actions - hard drives

Get Dell PowerEdge 1950 PDF manuals and user guides View all Dell PowerEdge 1950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Table 1-1. System Messages Message Causes Corrective Actions Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving. The memory configuration Ensure that the memory does not support node modules are installed in a interleaving, or the configuration that supports configuration has changed node interleaving. Check (for example, a failed other system messages for DIMM) so that node additional information interleaving cannot be for possible causes. For supported. The system memory configuration runs but with reduced information, see "General functionality. Memory Module Installation Guidelines" in the Hardware Owner's Manual. If the problem persists, see "Troubleshooting System Memory" in the Hardware Owner's Manual. !!*** Error: Remote Access Controller initialization failure *** RAC virtual USB devices may not be available... Remote Access Controller initialization failure. Ensure that the Remote Access Controller is properly installed. See "Installing a RAC Card" in the Hardware Owner's Manual. Invalid PCIe card found in the Internal_Storage slot! The system halted because Remove the PCIe an invalid PCIe expansion expansion card and install card is installed in the the internal SAS controller dedicated storage in the dedicated slot. controller slot. No boot device available Faulty or missing optical drive subsystem, hard drive, or hard-drive subsystem, or no bootable USB key installed. Use a bootable USB key, CD, or hard drive. See "Using the System Setup Program" in the Hardware Owner's Manual for information on setting the order of boot devices. Information Update 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Information Update
11
Table 1-1.
System Messages
Message
Causes
Corrective Actions
Alert! Node
Interleaving
disabled! Memory
configuration does
not support Node
Interleaving.
The memory configuration
does not support node
interleaving, or the
configuration has changed
(for example, a failed
DIMM) so that node
interleaving cannot be
supported.
The system
runs but with reduced
functionality.
Ensure that the memory
modules are installed in a
configuration that supports
node interleaving. Check
other system messages for
additional information
for possible causes. For
memory configuration
information, see "General
Memory Module
Installation Guidelines"
in the
Hardware Owner’s
Manual
. If the problem
persists, see
"Troubleshooting System
Memory" in the
Hardware
Owner’s Manual
.
!!*** Error: Remote
Access Controller
initialization
failure *** RAC
virtual USB devices
may not be
available...
Remote Access Controller
initialization failure.
Ensure that the Remote
Access Controller is
properly installed. See
"Installing a RAC Card"
in the
Hardware Owner’s
Manual
.
Invalid PCIe card
found in the
Internal_Storage
slot!
The system halted because
an invalid PCIe expansion
card is installed in the
dedicated storage
controller slot.
Remove the PCIe
expansion card and install
the internal SAS controller
in the dedicated slot.
No boot device
available
Faulty or missing optical
drive subsystem, hard
drive, or hard-drive
subsystem, or no bootable
USB key installed.
Use a bootable USB key,
CD, or hard drive. See
"Using the System Setup
Program" in the
Hardware
Owner’s Manual
for
information on setting
the order of boot devices.