Dell PowerEdge 1950 Information Update - Page 14

Warning! No micro - bios update

Get Dell PowerEdge 1950 PDF manuals and user guides View all Dell PowerEdge 1950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Table 1-1. System Messages (continued) Message Causes Corrective Actions TPM operation is pending. Press I to Ignore or M to Modify to allow this change and reset the system. WARNING: Modifying could prevent security. Configuration change has been requested. Press I to continue system boot. Press M to modify the TPM setting and restart. Warning: Following faulty DIMMs are disabled: DIMM n1 n2 Total memory size is reduced. Faulty or improperly seated See "Troubleshooting memory module(s). System Memory" in the DIMMs are disabled in Hardware Owner's Manual. pairs, as indicated by the n1 and n2. Check both DIMMs for a possible fault. Warning: A fatal error has caused system reset! Please check the system event log! A fatal system error occurred and caused the system to restart. Check the SEL for information that was logged during the error. See the applicable troubleshooting section in See "Troubleshooting Your System" in the Hardware Owner's Manual. for any faulty components specified in the SEL. Warning! No micro Micro code update failed. Update the BIOS firmware. code update loaded See "Getting Help" in the for processor n Hardware Owner's Manual. 14 Information Update

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
14
Information Update
TPM operation is
pending. Press I to
Ignore or M to
Modify to allow
this change and
reset the system.
WARNING: Modifying
could prevent
security.
Configuration change has
been requested.
Press
I
to continue system
boot. Press
M
to modify
the TPM setting and
restart.
Warning: Following
faulty DIMMs are
disabled:
DIMM
n
1
n
2
Total memory size
is reduced.
Faulty or improperly seated
memory module(s).
DIMMs are disabled in
pairs, as indicated by the
n
1
and
n
2
. Check both
DIMMs for a possible fault.
See "Troubleshooting
System Memory" in the
Hardware Owner’s Manual
.
Warning: A fatal
error has caused
system reset!
Please check the
system event log!
A fatal system error
occurred and caused the
system to restart.
Check the SEL for
information that was
logged during the error.
See the applicable
troubleshooting section in
See "Troubleshooting Your
System" in the
Hardware
Owner’s Manual
. for any
faulty components
specified in the SEL.
Warning! No micro
code update loaded
for processor
n
Micro code update failed.
Update the BIOS firmware.
See "Getting Help" in the
Hardware Owner’s Manual
.
Table 1-1.
System Messages
(continued)
Message
Causes
Corrective Actions