Dell PowerEdge R300 Hardware Owner's Manual (PDF) - Page 39

Install the NVRAM_CLR, Installing an Expansion - part numbers

Get Dell PowerEdge R300 PDF manuals and user guides View all Dell PowerEdge R300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Table 1-7. System Messages (continued) Message Causes Corrective Actions PCIe Fatal Error caused a system reset: Slot X PCI Express fatal errors occurred during the previous boot. Embedded Bus#XX/Dev#XX/Func X Reseat the PCIe card in the specified slot number. See "Installing an Expansion Card" on page 95. If the problem persists, see "Getting Help" on page 165. Please check the system event log for details Plug & Play Error encountered in Configuration Error initializing PCIe device; faulty system board. Install the NVRAM_CLR jumper and reboot the system. See Figure 6-1 for jumper location. If the problem persists, see "Troubleshooting Expansion Cards" on page 147. Read fault Requested sector not found The operating system Replace the USB medium or cannot read from the hard device. Ensure that the USB drive or USB device, the or hard drive cables are system could not find a properly connected. See particular sector on the "Troubleshooting a USB disk, or the requested Device" on page 127, sector is defective. "Troubleshooting an Internal USB Key" on page 137, and "Troubleshooting a Hard Drive" on page 142. Remote configuration update attempt failed System unable to process Retry Remote Configuration. Remote Configuration request. About Your System 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
About Your System
39
PCIe Fatal Error
caused a system
reset: Slot X
Embedded
Bus#XX/Dev#XX/Func
X
Please check the
system event log
for details
PCI Express fatal errors
occurred during the
previous boot.
Reseat the PCIe card in the
specified slot number. See
"Installing an Expansion
Card" on page 95. If the
problem persists, see
"Getting Help" on page 165.
Plug & Play
Configuration Error
Error encountered in
initializing PCIe device;
faulty system board.
Install the NVRAM_CLR
jumper and reboot the
system. See Figure 6-1 for
jumper location. If the
problem persists, see
"Troubleshooting Expansion
Cards" on page 147.
Read fault
Requested sector
not found
The operating system
cannot read from the hard
drive or USB device, the
system could not find a
particular sector on the
disk, or the requested
sector is defective.
Replace the USB medium or
device. Ensure that the USB
or hard drive cables are
properly connected. See
"Troubleshooting a USB
Device" on page 127,
"Troubleshooting an Internal
USB Key" on page 137, and
"Troubleshooting a Hard
Drive" on page 142.
Remote
configuration
update attempt
failed
System unable to process
Remote Configuration
request.
Retry Remote Configuration.
Table 1-7.
System Messages
(continued)
Message
Causes
Corrective Actions