Dell PowerEdge R830 Lifecycle Controller GUI v2.70.70.70 Users Guide - Page 14

Enabling Lifecycle Controller, Disabling Lifecycle Controller, Canceling Lifecycle Controller

Page 14 highlights

Message Lifecycle Controller not available Cause Resolution • 3 consecutive unsuccessful attempts to enter Lifecycle Controller GUI. • 3 consecutive unsuccessful attempts to complete inventory collection. • 3 consecutive unsuccessful attempts to perform tasks in Automated Task applications. Another process is using iDRAC. Wait for 30 minutes for the current process to complete, restart the system, and then retry. You can use the iDRAC GUI to check the job queue and the status. Related tasks Disabling Lifecycle Controller Enabling Lifecycle Controller To enable access to Lifecycle Controller during system startup: 1. Press during POST. The System Setup Main Menu page is displayed. 2. Select iDRAC Settings. The iDRAC Settings page is displayed. 3. Select Lifecycle Controller. 4. Under Lifecycle Controller, select Enabled. 5. On the System Setup Main Menu page, select Finish to save the settings. 6. Select Yes to restart the system. Disabling Lifecycle Controller To disable access to Lifecycle Controller at system startup: 1. Press during POST. The System Setup Main Menu page is displayed. 2. Select iDRAC Settings. The iDRAC Settings page is displayed. 3. Select Lifecycle Controller. 4. Under Lifecycle Controller, select Disabled. 5. On the System Setup Main Menu page, select Finish to save the settings. 6. Select Yes to restart the system. Canceling Lifecycle Controller actions If Lifecycle Controller causes the system to restart twice, cancel the Lifecycle Controller actions. However, if Lifecycle Controller causes the system to restart the third time, the message Lifecycle Controller update required is displayed, you must enable Lifecycle Controller. For more information on enabling Lifecycle Controller, see Enabling Lifecycle Controller. CAUTION: This action cancels all tasks that are being performed by Lifecycle Controller. It is recommended that you cancel the Lifecycle Controller actions only when absolutely necessary. 1. Press during POST. The System Setup Main Menu page is displayed. 2. In the System Setup Main Menu page, select iDRAC Settings. The iDRAC Settings page is displayed. 3. Select Lifecycle Controller. 4. Under Cancel Lifecycle Controller Actions, select Yes. 14 Using Lifecycle Controller

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86

Message
Cause
Resolution
3 consecutive unsuccessful attempts
to enter Lifecycle Controller GUI.
3 consecutive unsuccessful attempts
to complete inventory collection.
3 consecutive unsuccessful attempts
to perform tasks in Automated Task
applications.
Lifecycle Controller not available
Another process is using iDRAC.
Wait for 30 minutes for the current process
to complete, restart the system, and then
retry. You can use the iDRAC GUI to check
the job queue and the status.
Related tasks
Disabling Lifecycle Controller
Enabling Lifecycle Controller
To enable access to Lifecycle Controller during system startup:
1.
Press
<F2>
during POST.
The
System Setup Main Menu
page is displayed.
2.
Select
iDRAC Settings
.
The
iDRAC Settings
page is displayed.
3.
Select
Lifecycle Controller
.
4.
Under
Lifecycle Controller
, select
Enabled
.
5.
On the
System Setup Main Menu
page, select
Finish
to save the settings.
6.
Select
Yes
to restart the system.
Disabling Lifecycle Controller
To disable access to Lifecycle Controller at system startup:
1.
Press
<F2>
during POST.
The
System Setup Main Menu
page is displayed.
2.
Select
iDRAC Settings
.
The
iDRAC Settings
page is displayed.
3.
Select
Lifecycle Controller
.
4.
Under
Lifecycle Controller
, select
Disabled
.
5.
On the
System Setup Main Menu
page, select
Finish
to save the settings.
6.
Select
Yes
to restart the system.
Canceling Lifecycle Controller actions
If Lifecycle Controller causes the system to restart twice, cancel the Lifecycle Controller actions. However, if Lifecycle Controller causes
the system to restart the third time, the message
Lifecycle Controller update required
is displayed, you must enable
Lifecycle Controller. For more information on enabling Lifecycle Controller, see
Enabling Lifecycle Controller
.
CAUTION:
This action cancels all tasks that are being performed by Lifecycle Controller. It is recommended that you
cancel the Lifecycle Controller actions only when absolutely necessary.
1.
Press
<F2>
during POST.
The
System Setup Main Menu
page is displayed.
2.
In the
System Setup Main Menu
page, select
iDRAC Settings
.
The
iDRAC Settings
page is displayed.
3.
Select
Lifecycle Controller
.
4.
Under
Cancel Lifecycle Controller Actions
, select
Yes
.
14
Using Lifecycle Controller