Dell PowerEdge R830 Lifecycle Controller GUI v2.70.70.70 Users Guide - Page 51

System setup — Advanced Hardware Configuration

Get Dell PowerEdge R830 PDF manuals and user guides View all Dell PowerEdge R830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

1. Start Lifecycle Controller. 2. In the left pane, click Hardware Configuration. 3. In the right pane, click Configuration Wizards. 4. Under Storage Configuration wizards, click Break Mirror. The Break Mirror page is displayed with the mirrored virtual drives. 5. Select the related controller and click Finish. NOTE: The Break Mirror feature does not support software RAID controllers. NOTE: For more information about the break mirror feature, see the Performing a Break-Mirror Operation Using Lifecycle Controller white paper at www.delltechcenter.com/lc. The system automatically turns off even if one mirrored array is successfully delinked. System setup - Advanced Hardware Configuration The Lifecycle Controller Advanced Hardware Configuration wizards allow you to configure BIOS, iDRAC, and certain devices such as NIC, and RAID controllers through Human Interface Infrastructure (HII). HII is a UEFI-standard method for viewing and setting a device's configuration. You can utilize a single utility to configure multiple devices that may have different pre-boot configuration utilities. The utilities also provide localized versions of devices such as the BIOS setup. Based on the system configuration, other device types may also appear under Advanced Hardware Configuration if they support the HII configuration standard. NOTE: When you update the firmware on a BCM57xx and 57xxx adapters, you will notice that the cards are displayed as QLogic. This is due to the acquisition of Broadcom NetXtreme II by QLogic. The Advanced Hardware Configuration wizard allows you to configure the following: NOTE: You can also use System Setup utility during startup to configure the following devices. For more information about the System Setup utility, see Using The System Setup Program And Boot Manager. • System BIOS Settings • iDRAC Device Settings • NICs You can configure only one NIC at a time. The supported NIC cards are as follows: • BCM5708 TOE plus iSCSI Offload NIC • BCM5709C Dual Port NIC without iSCSI Offload • BCM5709C Dual Port Rack Mezzanine Card • BCM5709S Dual Port SERDES Mezzanine Card for Blade Systems • BCM57710 10GBase-T Single Port NIC • BCM57710 10GBase-T Dual Port Rack Mezzanine Card • BCM57710 Dual Port KX4 Blade Mezzanine Card • BCM57711 Dual Port KX4 Noble MC • BCM95708C PCI-E NIC • BCM95709C 10/100/1000BASET Quad Port NIC • BCM95709 iSCSI Offload Dual Port NIC • BCM957711 10G SFP+ Dual Port NIC • Broadcom 57810S DP 10G SFP+ Adapter (Full Height) • Broadcom 57810S DP 10G SFP+ Adapter (Low Profile) • Broadcom 57800S DP 10G BASE-T Adapter (Full Height) • Broadcom 57800S DP 10G BASE-T Adapter (Low Profile) • Broadcom 5720 DP 1G Adapter (Full Height) • Broadcom 5720 DP 1G Adapter (Low Profile) • Broadcom 5719 QP 1G Adapter (Full Height) • Broadcom 5719 QP 1G Adapter (Low Profile) • Broadcom 57800S QP rNDC (10G BASE-T + 1G BASE-T) • Broadcom 57800S QP rNDC (10G SFP+ + 1G BASE-T) Configure 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
1.
Start Lifecycle Controller.
2.
In the left pane, click
Hardware Configuration
.
3.
In the right pane, click
Configuration Wizards
.
4.
Under
Storage Configuration wizards
, click
Break Mirror
.
The
Break Mirror
page is displayed with the mirrored virtual drives.
5.
Select the related controller and click
Finish
.
NOTE:
The Break Mirror feature does not support software RAID controllers.
NOTE:
For more information about the break mirror feature, see the
Performing a Break-Mirror Operation Using
Lifecycle Controller
white paper at
www.delltechcenter.com/lc
.
The system automatically turns off even if one mirrored array is successfully delinked.
System setup — Advanced Hardware
Configuration
The Lifecycle Controller
Advanced Hardware Configuration
wizards allow you to configure BIOS, iDRAC, and certain devices such as
NIC, and RAID controllers through Human Interface Infrastructure (HII). HII is a UEFI-standard method for viewing and setting a device's
configuration. You can utilize a single utility to configure multiple devices that may have different pre-boot configuration utilities. The
utilities also provide localized versions of devices such as the BIOS setup.
Based on the system configuration, other device types may also appear under
Advanced Hardware Configuration
if they support the
HII configuration standard.
NOTE:
When you update the firmware on a BCM57xx and 57xxx adapters, you will notice that the cards are displayed as
QLogic. This is due to the acquisition of Broadcom NetXtreme II by QLogic.
The
Advanced Hardware Configuration
wizard allows you to configure the following:
NOTE:
You can also use System Setup utility during startup to configure the following devices. For more information
about the System Setup utility, see
Using The System Setup Program And Boot Manager
.
•
System BIOS Settings
•
iDRAC Device Settings
•
NICs
You can configure only one NIC at a time. The supported NIC cards are as follows:
•
BCM5708 TOE plus iSCSI Offload NIC
•
BCM5709C Dual Port NIC without iSCSI Offload
•
BCM5709C Dual Port Rack Mezzanine Card
•
BCM5709S Dual Port SERDES Mezzanine Card for Blade Systems
•
BCM57710 10GBase-T Single Port NIC
•
BCM57710 10GBase-T Dual Port Rack Mezzanine Card
•
BCM57710 Dual Port KX4 Blade Mezzanine Card
•
BCM57711 Dual Port KX4 Noble MC
•
BCM95708C PCI-E NIC
•
BCM95709C 10/100/1000BASET Quad Port NIC
•
BCM95709 iSCSI Offload Dual Port NIC
•
BCM957711 10G SFP+ Dual Port NIC
•
Broadcom 57810S DP 10G SFP+ Adapter (Full Height)
•
Broadcom 57810S DP 10G SFP+ Adapter (Low Profile)
•
Broadcom 57800S DP 10G BASE-T Adapter (Full Height)
•
Broadcom 57800S DP 10G BASE-T Adapter (Low Profile)
•
Broadcom 5720 DP 1G Adapter (Full Height)
•
Broadcom 5720 DP 1G Adapter (Low Profile)
•
Broadcom 5719 QP 1G Adapter (Full Height)
•
Broadcom 5719 QP 1G Adapter (Low Profile)
•
Broadcom 57800S QP rNDC (10G BASE-T + 1G BASE-T)
•
Broadcom 57800S QP rNDC (10G SFP+ + 1G BASE-T)
Configure
51