Dell PowerEdge T20 Dell PowerEdge T20 Owners Manual - Page 69

Troubleshooting An Optical Drive, Troubleshooting A Hard Drive

Get Dell PowerEdge T20 PDF manuals and user guides View all Dell PowerEdge T20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

14. Close the system. 15. As the system boots, observe any error message that is displayed and the diagnostic indicators on the front of the system. 16. If the memory problem is still indicated, repeat step 12 through step 15 for each memory module installed. If the problem persists after all memory modules have been checked, see Getting Help. Troubleshooting An Optical Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Try using a different CD or DVD. 2. Enter the System Setup and ensure that the integrated SATA controller and the drive's SATA port are enabled. 3. Run the appropriate diagnostic test. 4. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. 5. Open the system. 6. Remove the front bezel. 7. Ensure that the interface cable is securely connected to the drive and to the controller. 8. Ensure that a power cable is properly connected to the drive. 9. Close the system. If the problem is not resolved, see Getting Help. Troubleshooting A Hard Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. CAUTION: This troubleshooting procedure can erase data stored on the hard drive. Before you proceed, back up all files on the hard drive. 1. Run the appropriate diagnostic test. For more information, see Using System Diagnostics. Depending on the results of the diagnostics test, proceed as needed through the following steps. 2. Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information. 3. Restart the system and enter the System Setup. 4. Verify that the controller is enabled and the drives are displayed in the System Setup. If the problem persists, try troubleshooting the expansion cards or see Getting Help. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
14.
Close the system.
15.
As the system boots, observe any error message that is displayed and the diagnostic indicators on the front of the
system.
16.
If the memory problem is still indicated, repeat step 12 through step 15 for each memory module installed.
If the problem persists after all memory modules have been checked, see
Getting Help
.
Troubleshooting An Optical Drive
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1.
Try using a different CD or DVD.
2.
Enter the System Setup and ensure that the integrated SATA controller and the drive's SATA port are enabled.
3.
Run the appropriate diagnostic test.
4.
Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
5.
Open the system.
6.
Remove the front bezel.
7.
Ensure that the interface cable is securely connected to the drive and to the controller.
8.
Ensure that a power cable is properly connected to the drive.
9.
Close the system.
If the problem is not resolved, see
Getting Help
.
Troubleshooting A Hard Drive
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
CAUTION: This troubleshooting procedure can erase data stored on the hard drive. Before you proceed, back up
all files on the hard drive.
1.
Run the appropriate diagnostic test. For more information, see
Using System Diagnostics
.
Depending on the results of the diagnostics test, proceed as needed through the following steps.
2.
Ensure that the required device drivers for your controller card are installed and are configured correctly. See the
operating system documentation for more information.
3.
Restart the system and enter the System Setup.
4.
Verify that the controller is enabled and the drives are displayed in the System Setup.
If the problem persists, try troubleshooting the expansion cards or see
Getting Help
.
69