Dell PowerEdge XE2420 EMC Technical Specifications - Page 5

PowerEdge XE2420 system overview, Front view of the System

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

1 PowerEdge XE2420 system overview The PowerEdge XE2420 system is a 2U server that supports: • Two Intel Xeon Cascade Lake scalable processors up to 150 W • 16 DDR4 RDIMM and Load Reduced DIMM • Two, or four, 2.5-inch SATA, SAS, NVMe, or six EDSFF E1.L drives configuration. • BOSS dual SATA M.2 boot card • Two redundant 2000 W AC PSUs and 1100 W DC PSUs NOTE: For more information about how to hot swap NVMe PCIe SSD U.2 device, see the Dell Express Flash NVMe PCIe SSD User's Guide at https://www.dell.com/support> Browse all Products > Data Center Infrastructure > Storage Adapters & Controllers > Dell PowerEdge Express Flash NVMe PCIe SSD > Documentation > Manuals and Documents. NOTE: All instances of SAS, SATA drives are seen as drives in this document, unless specified otherwise. NOTE: In 2C configuration, hard drive slots 2 and 3 do not support NVMe drives if only processor 1 is installed. For more information about supported drives, see the Drive specifications section. NOTE: The PowerEdge XE2420 system is suitable for installation in Network Telecommunications Facilities (NTF), and locations where the National Electrical Code (NEC) applies. NOTE: The PowerEdge XE2420 system is suitable for Common Bonding Networks (CBNs). Topics: • Front view of the System • Rear view of the system Front view of the System Figure 1. Front view of 2 x 2.5-inch drive system Table 1. Front view of 2 x 2.5-inch drive system Item Ports, panels, and slots 1 Serial port Icon IOIOI 2 GPU riser 1 slots N/A Description Enables you to connect a serial device to the system. For more information, see the Technical specifications section. The GPU card slot (riser 1) connects up to two full-height PowerEdge XE2420 system overview 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
PowerEdge XE2420 system overview
The PowerEdge XE2420 system is a 2U server that supports:
•
Two Intel Xeon Cascade Lake scalable processors up to 150 W
•
16 DDR4 RDIMM and Load Reduced DIMM
•
Two, or four, 2.5-inch SATA, SAS, NVMe, or six EDSFF E1.L drives configuration.
•
BOSS dual SATA M.2 boot card
•
Two redundant 2000 W AC PSUs and 1100 W DC PSUs
NOTE:
For more information about how to hot swap NVMe PCIe SSD U.2 device, see the
Dell Express Flash NVMe PCIe
SSD User's Guide
at
> Browse all Products > Data Center Infrastructure >
Storage
Adapters & Controllers > Dell PowerEdge Express Flash NVMe PCIe SSD > Documentation > Manuals and Documents.
NOTE:
All instances of SAS, SATA drives are seen as drives in this document, unless specified otherwise.
NOTE:
In 2C configuration, hard drive slots 2 and 3 do not support NVMe drives if only processor 1 is installed.
For more information about supported drives, see the
Drive specifications
section.
NOTE:
The PowerEdge XE2420 system is suitable for installation in Network Telecommunications Facilities (NTF), and
locations where the National Electrical Code (NEC) applies.
NOTE:
The PowerEdge XE2420 system is suitable for Common Bonding Networks (CBNs).
Topics:
•
Front view of the System
•
Rear view of the system
Front view of the System
Figure 1. Front view of 2 x 2.5-inch drive system
Table 1. Front view of 2 x 2.5-inch drive system
Item
Ports, panels, and slots
Icon
Description
1
Serial port
IOIOI
Enables you to connect a serial
device to the system. For more
information, see the
Technical
specifications
section.
2
GPU riser 1 slots
N/A
The GPU card slot (riser 1)
connects up to two full-height
1
PowerEdge XE2420 system overview
5