Dell PowerStore 1200T EMC PowerStore Installation and Service Guide for PowerS - Page 23

Removing a filler panel, Install the rails in the cabinet, About this task, Steps

Get Dell PowerStore 1200T PDF manuals and user guides View all Dell PowerStore 1200T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Removing a filler panel About this task In most cases, the front space into which you will install the enclosure is covered by a filler panel, which is attached to latch brackets. If one or more filler panels cover the space where you want to install the enclosure, remove each panel using the procedure that follows. Steps 1. Remove the filler panel. 2. Use a flatblade screwdriver or similar tool to pry off the latch brackets (Prying off a latch bracket on page 23). CL4064 Figure 12. Prying off a latch bracket Install the rails in the cabinet This task describes the procedure to install one rail. After installing one rail, repeat the procedure for the other rail. The procedure is the same for both the left and right rail. You can install the rails into either a square or round hole rack. Steps 1. Position the rail end piece so the label FRONT is located at the front of the rack and facing towards the inside of the rack, while orienting the rear of the rail to align level with the holes on the rear of the rack. 2. From the rear of the rack, pull the rail straight back until the latch is locked. 3. To install the front end piece of the rail, press the blue latch release button until the latch rotates open. 4. Pull the rail forward until the pins slide into the holes on the front of the rack, then release the latch to secure the rail in place. Install a new base enclosure and optional expansion enclosure 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
Removing a filler panel
About this task
In most cases, the front space into which you will install the enclosure is covered by a filler panel, which is attached to latch
brackets. If one or more filler panels cover the space where you want to install the enclosure, remove each panel using the
procedure that follows.
Steps
1.
Remove the filler panel.
2.
Use a flatblade screwdriver or similar tool to pry off the latch brackets (
Prying off a latch bracket
on page 23).
CL4064
Figure 12. Prying off a latch bracket
Install the rails in the cabinet
This task describes the procedure to install one rail. After installing one rail, repeat the procedure for the other rail. The
procedure is the same for both the left and right rail. You can install the rails into either a square or round hole rack.
Steps
1.
Position the rail end piece so the label FRONT is located at the front of the rack and facing towards the inside of the rack,
while orienting the rear of the rail to align level with the holes on the rear of the rack.
2.
From the rear of the rack, pull the rail straight back until the latch is locked.
3.
To install the front end piece of the rail, press the blue latch release button until the latch rotates open.
4.
Pull the rail forward until the pins slide into the holes on the front of the rack, then release the latch to secure the rail in
place.
Install a new base enclosure and optional expansion enclosure
23