Dell PowerStore 3200T EMC PowerStore Installation and Service Guide for PowerS - Page 32
Installing the NVMe expansion enclosure rails front, Adding the retaining screws
View all Dell PowerStore 3200T manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
Figure 21. Installing the NVMe expansion enclosure rails (front) 5. Add the retaining screws that came with the rails to the front and back of both rails. NOTE: Use the washers that came with the rails if the rack holes are square. NOTE: The screw hole at the front of the rail is behind the rail clamp. NOTE: You will need a long handled screwdriver to reach the screw hole at the rear of the rack. NOTE: The following illustration does not show the C-clips that are used to attach the cable management arms. Figure 22. Adding the retaining screws 32 Install a new base enclosure and optional expansion enclosure
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
Figure 21. Installing the NVMe expansion enclosure rails (front)
5.
Add the retaining screws that came with the rails to the front and back of both rails.
NOTE:
Use the washers that came with the rails if the rack holes are square.
NOTE:
The screw hole at the front of the rail is behind the rail clamp.
NOTE:
You will need a long handled screwdriver to reach the screw hole at the rear of the rack.
NOTE:
The following illustration does not show the C-clips that are used to attach the cable management arms.
Figure 22. Adding the retaining screws
32
Install a new base enclosure and optional expansion enclosure