Dell PowerVault MD3000i Installation Guide - Page 53

If you are using SLES10 SP1 via the GUI, Desktop, iSCSI Initiator, Service Start, When Booting

Get Dell PowerVault MD3000i PDF manuals and user guides View all Dell PowerVault MD3000i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

discovery.sendtargets.auth.password = password_1 discovery.sendtargets.auth.username = iqn.198405.com.dell:powervault.123456 discovery.sendtargets.auth.password_in = test1234567890 If you are using SLES10 SP1 via the GUI 1 Select Desktop→ YaST→ iSCSI Initiator. 2 Click Service Start, then select When Booting. 3 Select Discovered Targets, then select Discovery. 4 Enter the IP address of the port. 5 Click Next. 6 Select any target that is not logged in and click Log in. 7 Choose one: • If you are not using CHAP authentication, select No Authentication. Proceed to step 8. or • If you are using CHAP authentication, enter the CHAP username and password. To enable Mutual CHAP, select and enter the Mutual CHAP username and password. 8 Repeat step 7 for each target until at least one connection is logged in for each controller. 9 Go to Connected Targets. 10 Verify that the targets are connected and show a status of true. Setting Up Your iSCSI Storage Array 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Setting Up Your iSCSI Storage Array
53
discovery.sendtargets.auth.password = password_1
discovery.sendtargets.auth.username = iqn.1984-
05.com.dell:powervault.123456
discovery.sendtargets.auth.password_in = test1234567890
If you are using SLES10 SP1 via the GUI
1
Select
Desktop
→
YaST
→
iSCSI Initiator
.
2
Click
Service Start
, then select
When Booting
.
3
Select
Discovered Targets
, then select
Discovery
.
4
Enter the IP address of the port.
5
Click
Next
.
6
Select any target that is not logged in and click
Log in
.
7
Choose one:
•
If you are not using CHAP authentication, select
No Authentication
. Proceed to step 8.
or
•
If you are using CHAP authentication, enter the CHAP username and password. To enable
Mutual CHAP, select and enter the Mutual CHAP username and password.
8
Repeat step 7 for each target until at least one connection is logged in for each controller.
9
Go to
Connected Targets
.
10
Verify that the targets are connected and show a status of
true
.