Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 28

General settings, Con VLANs

Get Dell S5148F-ON PDF manuals and user guides View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

7.2.1 General settings Configure the hostname, OOB management IP address and default gateway. Specify an NTP server accessible by the switch. In this example, this is an NTP server on the OOB management network, with a different IP address than that used by the VxRail nodes on the in-band management network. Enable RSTP as a precaution against loops. Configure S5148F-Leaf1A as the primary RSTP root bridge using the spanning-tree rstp priority 0 command and S5148F-Leaf1B as the secondary RSTP root bridge using the spanning-tree rstp priority 4096 command. Note: In OS10EE, LLDP is enabled on each interface and globally by default. LLDP is useful for troubleshooting and validation. Dell EMC recommends leaving it enabled. General settings - dual switch without VLT S5148F-Leaf1A S5148F-Leaf1B configure terminal configure terminal hostname S5148F-Leaf1A hostname S5148F-Leaf1B interface mgmt1/1/1 no ip address ip address 100.67.172.38/24 no shutdown management route 0.0.0.0/0 100.67.172.254 interface mgmt1/1/1 no ip address ip address 100.67.172.37/24 no shutdown management route 0.0.0.0/0 100.67.172.254 ntp server 100.67.10.20 ntp server 100.67.10.20 spanning-tree mode rstp spanning-tree rstp priority 0 spanning-tree mode rstp spanning-tree rstp priority 4096 7.2.2 Configure VLANs In this section, VLANs are configured per Table 2. Create the in-band management VLAN and assign a unique IP address on each switch. Configure VRRP to provide gateway redundancy. Set the VRRP priority. The switch with the largest priority value becomes the master VRRP router. Assign the same virtual address to both switches. Create the vMotion, vSAN, and VM Network VLANs. Configure VLANs - dual switch without VLT S5148F-Leaf1A S5148F-Leaf1B interface vlan1611 description InBand_Mgmt ip address 172.16.11.253/24 vrrp-group 11 priority 150 virtual-address 172.16.11.254 no shutdown interface vlan1611 description InBand_Mgmt ip address 172.16.11.252/24 vrrp-group 11 priority 100 virtual-address 172.16.11.254 no shutdown interface vlan1612 description vMotion no shutdown interface vlan1612 description vMotion no shutdown 28 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON, S5232F-ON and S5148F-ON

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
28
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON,
S5232F-ON and S5148F-ON
7.2.1
General settings
Configure the hostname, OOB management IP address and default gateway. Specify an NTP server
accessible by the switch. In this example, this is an NTP server on the OOB management network, with a
different IP address than that used by the VxRail nodes on the in-band management network. Enable RSTP
as a precaution against loops. Configure S5148F-Leaf1A as the primary RSTP root bridge using the
spanning-tree rstp priority 0
command and S5148F-Leaf1B as the secondary RSTP root bridge
using the
spanning-tree rstp priority 4096
command.
Note:
In OS10EE, LLDP is enabled on each interface and globally by default. LLDP is useful for
troubleshooting and validation. Dell EMC recommends leaving it enabled.
General settings - dual switch without VLT
S5148F-Leaf1A
S5148F-Leaf1B
configure terminal
hostname S5148F-Leaf1A
interface mgmt1/1/1
no ip address
ip address 100.67.172.38/24
no shutdown
management route 0.0.0.0/0
100.67.172.254
ntp server 100.67.10.20
spanning-tree mode rstp
spanning-tree rstp priority 0
configure terminal
hostname S5148F-Leaf1B
interface mgmt1/1/1
no ip address
ip address 100.67.172.37/24
no shutdown
management route 0.0.0.0/0
100.67.172.254
ntp server 100.67.10.20
spanning-tree mode rstp
spanning-tree rstp priority 4096
7.2.2
Configure VLANs
In this section, VLANs are configured per Table 2.
Create the in-band management VLAN and assign a unique IP address on each switch. Configure VRRP to
provide gateway redundancy. Set the VRRP priority. The switch with the largest priority value becomes the
master VRRP router. Assign the same virtual address to both switches.
Create the vMotion, vSAN, and VM Network VLANs.
Configure VLANs - dual switch without VLT
S5148F-Leaf1A
S5148F-Leaf1B
interface vlan1611
description InBand_Mgmt
ip address 172.16.11.253/24
vrrp-group 11
priority 150
virtual-address 172.16.11.254
no shutdown
interface vlan1612
description vMotion
no shutdown
interface vlan1611
description InBand_Mgmt
ip address 172.16.11.252/24
vrrp-group 11
priority 100
virtual-address 172.16.11.254
no shutdown
interface vlan1612
description vMotion
no shutdown